- 您現在的位置：買賣IC網 > PDF目錄374254 > K3NC-PB2C (Omron Electronics LLC) Up/Down Counting Meter PDF資料下載
參數資料
| 型號： | K3NC-PB2C |
| 廠商： | Omron Electronics LLC |
| 英文描述： | Up/Down Counting Meter |
| 中文描述： | 上/下計數儀 |
| 文件頁數： | 19/23頁 |
| 文件大?。?/td> | 669K |
| 代理商： | K3NC-PB2C |
Up/Down Counting Meter
K3NC
C-149
C
I
Setting Procedures
The K3NC has four modes: RUN mode for normal operations, Setting mode for initial parameter input, Protect mode for lock-out configuration, and
Maintenance mode for initializing set values. The parameters that are accessible on any individual K3NC will vary depending on the Output Board
installed. Refer to the
K3NC Operation Manual
for details.
RUN Mode:
Remains in this mode under normal operation.
The process value can be monitored.
Using the front panel keys, the comparative set value can be changed and counting value reset can be performed.
Setting Mode:
Used for making initial settings.
Includes settings for four menus (Set value (
sUset
), prescaling (
Protect Mode:
Used for locking the front key operation or parameter changes.
Maintenance Mode:
Used for initializing set values.
pscl
), setup (
setup
), option (
opt
)) and the output test.
sUset
- Program set values
Select bank no. of set values
sU
*
.01
Enter set value OUT1 of bank 1
sU
*
.02
Enter set value OUT2 of bank 1
sU
*
.03
Enter set value OUT3 of bank 1
sU
*
.04
Enter set value OUT4 of bank 1
sU
*
.05
Enter set value OUT5 of bank 1
Note:
The above is an example when the bank number is set to 1.
- Display prescaling
Select bank no. of prescale values
ps
*
.ax
Set the mantissa (X) of the prescale value
ps
*
.ay
Set the exponent (Y) of the prescale value
decp.
*
Select decimal point
Note:
The above is an example when the bank number is set to 1.
- Program input mode/input sensor/serial communications
Specify input mode
in
Select a sensor type
u-no
Enter the unit no. for the host
bps
Select the baud rate
len
Select the word bit length
sbit
Select the stop bits
prty
Select the parity bits
- Supplementary settings related to display or control
Select power failure memory function
compn
Set compensation value
con-p
Select conditions that allow compensation input
out
Select output mode
lset.h
Enter the upper limit (H) of linear output range
lset.l
Enter the lower limit (L) of linear output range
r-l
Select the remote/local programming
- Generating simulated input for testing the output function
- Program lock-out configuration
Enable all key protection
sUset
Enable set value change prohibition
s.bank
pscl
p.bank
setup
count
opt
memo
test
prot
all
reset
Enable prohibition of counting value reset using the front
panel keys
Specify the menus to be protected against setting in the
setting mode
secr
1 s
1 s
+
+
ESC
ESC
ESC
ESC
Power ON
RUN mode
Setting mode
Maintenance mode
Protect mode
When power is ON
相關PDF資料 |
PDF描述 |
|---|---|
| K3S7V2000M-TC | 64M-Bit (4Mx16 /2Mx32) Synchronous MASKROM |
| K3S7V2000M-TC10 | 64M-Bit (4Mx16 /2Mx32) Synchronous MASKROM |
| K3S7V2000M-TC12 | 64M-Bit (4Mx16 /2Mx32) Synchronous MASKROM |
| K3S7V2000M-TC15 | 64M-Bit (4Mx16 /2Mx32) Synchronous MASKROM |
| K3S7V2000M-TC20 | 64M-Bit (4Mx16 /2Mx32) Synchronous MASKROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K3NHTA1C | 功能描述:控制器 RoHS:否 制造商:Omron Industrial 模擬/數字:Digital 類型:Digital Temperature Controller 顯示器類型:11-Segment, 4 Digit 電源電壓:100 VAC to 240 VAC 安裝: 控制方法: 大小:48 mm x 48 mm |
| K3NHTA2A | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Accessories, Temperature/Process Meter |
| K3NHTA2C | 制造商:Omron Electronic Components LLC 功能描述:Temperature/Process Meter 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Temperature/Process Meter |
| K3NPNB1A | 制造商:Omron Electronic Components LLC 功能描述:Time/Period Meter, Base Unit 100 To 240 VAC Supply Voltage 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Time/Period Meter, Base Unit 100 To 240 VAC Supply Voltage |
| K3NPNB1C | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Time/Period Meter |
發布緊急采購，3分鐘左右您將得到回復。