- 您現在的位置：買賣IC網 > PDF目錄374311 > KB2514 (SAMSUNG SEMICONDUCTOR CO. LTD.) VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS PDF資料下載
參數資料
| 型號： | KB2514 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS |
| 中文描述： | 視頻放大器合并OSD處理器的顯示器 |
| 文件頁數： | 50/55頁 |
| 文件大小： | 563K |
| 代理商： | KB2514 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁
VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS
KB2514
49
Preliminary
RECOMMENDATION
5V Power Routing
KB2514's OSD part power is composed of analog VDD and digital VDD. To eliminate clock noise influence in the
digital block, you need to separate the analog VDDA and digital VDD.
(BD102 use: Refer to Application Circuit )
12V Power Routing
Because KB2514 is a wideband AMP of above 150MHz, 12V power significantly affects the video characteristics.
The effects from the inductance and capacitance are different for each board, and , therefore, some tuning is
required to obtain the optimum performance. The output power, VCC2, must be separated from VCC1 and VCC3
using a coil, which is parallel-connected to the damping resistor.The appropriate coil value is between 20uH -
200uH. Parallel-connected a variable resistor to the coil and control its resistance to obtain the optimum video
waveform.
(Moreover, BD103 can tune using a coil and variable resistor to obtain the optimum video waveform.
L103, R124, BD103: Refer to application circuit)
VCC1, VCC3 12V Power
Use a 104 capacitor and large capacitor greater than 470uH for the power filter capacitor.
12V Output Stage Power VCC2
Do not use the power filter capacitor.
5V Digital Power VDD
Don't use a coil or magnetic core to the VDD input. Make the power filter capacitor, an electric capacitor of greater
than 50uF, single and connect it to VSS, the digital GND.
Output Stage GND2
Care must be taken during routing because it ,as an AMP output stage GND, is an important factor of video
oscillation. R/G/B clamp cap and R/G/B load resistor must be placed as close as possible to the GND2 pin. GND2
must be arranged so that it has the minimum GND loop, which at one point must be connected to the main GND.
Digital GND VSS
When this is to be connected directly to the GND2, it can cause the OSD clock noise, so the loop connection
should be routed as far away as possible. If the OSD clock noise affects the screen, separate VSS GND from all
GND and connect it to the main board using a bead. Again, the bead connection point should be placed as far
away as possible to the GND2.
Analog Block
The PLL built in to KB2514 is sensitive to noise due to the wide range PLL characteristics. Therefore, you need to
isolate the analog block in the following manner. First make a separate land for the analog block (pin2 - pin6)'s
ground, and connect it to the main ground through a 1M
resistor. The analog GND of both sides of a double faced
PCB must be separated from the main ground. (Separate pin 2's 5V analog GND, which is the GND for OSD PLL,
from the main and digital GNDs and connect it to the main GND using about 1M
resistor. GND for pins 2 - 6 is the
No. 2 VSSA GND.)
相關PDF資料 |
PDF描述 |
|---|---|
| KB2516 | TRIPLE 8-BIT ANALOG-TO-DIGITAL CONVERTER |
| KB9223 | RF AMP & SERVO SIGNAL PROCESSOR |
| KB9223-L | RF AMP & SERVO SIGNAL PROCESSOR |
| KB9224 | VIDEO-CD 2ND GENERATION |
| KBA-20 | Tantalum Molded Capacitor; Capacitance: .68uF; Voltage: 25V; Case Size: 3.2x1.6 mm; Packaging: Tape & Reel |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KB2516 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:TRIPLE 8-BIT ANALOG-TO-DIGITAL CONVERTER |
| KB2531S28 | 功能描述:POT 25K OHM 2W REV LOG TAPER RoHS:是 類別:電位計，可變電阻器 >> 旋轉 - 對數 系列:K 標準包裝:25 系列:51 電阻（歐姆）:10k 功率（瓦特）:0.25W，1/4W 容差:±20% 溫度系數:±1000ppm/°C 匝數:單路 旋轉:290° 調節型:側面調節 電阻材料:導電塑料 端接類型:PCB 引腳 觸動器長度:0.875"（22.22mm） 觸動器類型:開槽軸 觸動器直徑:0.125"（3.18mm） 尺寸 - 主體:方形 - 0.350" L x 0.492" W x 0.522" H（8.89mm x 12.50mm x 13.25mm） 安裝類型:通孔 包裝:散裝 |
| KB2541S28 | 功能描述:POT 250K OHM 2W REV LOG TAPER RoHS:是 類別:電位計，可變電阻器 >> 旋轉 - 對數 系列:K 標準包裝:25 系列:51 電阻（歐姆）:10k 功率（瓦特）:0.25W，1/4W 容差:±20% 溫度系數:±1000ppm/°C 匝數:單路 旋轉:290° 調節型:側面調節 電阻材料:導電塑料 端接類型:PCB 引腳 觸動器長度:0.875"（22.22mm） 觸動器類型:開槽軸 觸動器直徑:0.125"（3.18mm） 尺寸 - 主體:方形 - 0.350" L x 0.492" W x 0.522" H（8.89mm x 12.50mm x 13.25mm） 安裝類型:通孔 包裝:散裝 |
| KB2550CGKD | 功能描述:LED條和陣列 8.89X3.81MM GRN LT BAR LED DISPLAY RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| KB-2550CGKD | 制造商:Kingbright Corporation 功能描述:LIGHT BAR GREEN 制造商:Kingbright Corporation 功能描述:LIGHT BAR, GREEN 制造商:Kingbright Corporation 功能描述:LIGHT BAR, GREEN; LED Configuration:Bar; LED Color:Green; Forward Voltage:2.1V; Forward Current If:20mA; No. of LEDs:4; Luminous Intensity:110mcd; Display Size:19.05mm x 3.81mm ;RoHS Compliant: Yes 制造商:Kingbright Corporation 功能描述:LED Light Bar,Green,50mcd,20mA |
發布緊急采購，3分鐘左右您將得到回復。