- 您現在的位置：買賣IC網 > PDF目錄374311 > KBE00S009M-D411 (SAMSUNG SEMICONDUCTOR CO. LTD.) 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 PDF資料下載
參數資料
| 型號： | KBE00S009M-D411 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2 |
| 中文描述： | 1Gb的NAND × 2 256Mb的移動SDRAM × 2 |
| 文件頁數： | 15/86頁 |
| 文件大?。?/td> | 1898K |
| 代理商： | KBE00S009M-D411 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
MCP MEMORY
15
KBE00S009M-D411
Revision 1.0
May 2005
NAND Flash Technical Notes
Initial Invalid Block(s)
Initial invalid blocks are defined as blocks that contain one or more initial invalid bits whose reliability is not guaranteed by Samsung.
The information regarding the initial invalid block(s) is so called as the initial invalid block information. Devices with initial invalid
block(s) have the same quality level as devices with all valid blocks and have the same AC and DC characteristics. An initial invalid
block(s) does not affect the performance of valid block(s) because it is isolated from the bit line and the common source line by a
select transistor. The system design must be able to mask out the initial invalid block(s) via address mapping. The 1st block, which is
placed on 00h block address, is fully guaranteed to be a valid block, does not require Error Correction up to 1K Program/Erase
cycles.
Identifying Initial Invalid Block(s)
All device locations are erased(FFh) except locations where the initial invalid block(s) information is written prior to shipping. The
initial invalid block(s) status is defined by the 6th byte in the spare area. Samsung makes sure that either the 1st or 2nd page of
every initial invalid block has non-FFh data at the column address of 517. Since the initial invalid block information is also erasable
in most cases, it is impossible to recover the information once it has been erased. Therefore, the system must be able to recognize
the initial invalid block(s) based on the initial invalid block information and create the initial invalid block table via the following sug-
gested flow chart(Figure 4). Any intentional erasure of the initial invalid block information is prohibited.
*
Check "FFh" at the column address 517
of the 1st and 2nd page in the block
Figure 4. Flow chart to create initial invalid block table.
Start
Set Block Address = 0
Check "FFh"
Increment Block Address
Last Block
End
No
Yes
Yes
Create (or update)
Initial Invalid
Block(s) Table
No
相關PDF資料 |
PDF描述 |
|---|---|
| KBJ2501 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2502 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2503 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2504 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
| KBJ2505 | 25A SINGLE PHASE SILICON BRIDGE RECTIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KB-E100SRW | 功能描述:LED 顯示器和配件 Red 640nm 90mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| KB-E100SURKW | 功能描述:LED條和陣列 8.89X3.81MM RED LT BAR LED DISPLAY RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube |
| KBE1A11N | 制造商:Lovato Electric Inc 功能描述: |
| KBEV 5T-0.5-RSSV 4.5T | 制造商:TURCK Inc 功能描述:KBEV 5T-0.5-RSSV 4.5T |
| KB-F100SRW | 功能描述:LED 顯示器和配件 Red 640nm 200mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。