參數資料
型號： KBE00S009M-D411
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： 1Gb NAND x 2 + 256Mb Mobile SDRAM x 2
中文描述： 1Gb的NAND × 2 256Mb的移動SDRAM × 2
文件頁數： 63/86頁
文件大?。?/td> 1898K
代理商： KBE00S009M-D411
MCP MEMORY
63
KBE00S009M-D411
Revision 1.0
May 2005
tSS
*1
tSS
*2
Auto Refresh
Command
PRE
t
RP(min)
t
ARFC(min)
～
Auto
Refresh
CKE = High
CMD
An auto refresh command is issued by having CS, RAS and CAS held low with CKE and WE high at the rising edge of the
clock(CLK). All banks must be precharged and idle for t
RP
(min) before the auto refresh command is applied. No control of the external
address pins is required once this cycle has started because of the internal address counter. When the refresh cycle has completed,
all banks will be in the idle state. A delay between the auto refresh command and the next activate command or subsequent auto
refresh command must be greater than or equal to the t
ARFC
(min).
～
～
CLK
A Self Refresh command is defined by having CS, RAS, CAS and CKE held low with WE high at the rising edge of the clock. Once
the self Refresh command is initiated, CKE must be held low to keep the device in Self Refresh mode. After 1 clock cycle from the self
refresh command, all of the external control signals including system clock(CLK) can be disabled except CKE. The clock is internally
disabled during Self Refresh operation to reduce power. To exit the Self Refresh mode, supply stable clock input before returning CKE
high, assert deselect or NOP command and then assert CKE high. In case that the system uses burst auto refresh during normal
opreation, it is recommended to use burst 4096 auto refresh cycle immediately before entering self refresh mode and after exiting in
self refresh mode. On the other hand, if the system uses the distributed auto refresh, the system only has to keep the refresh duty
cycle.
Self Refresh
Command
CKE
Stable Clock
t
SS
NOP
Self
Refresh
CLK
t
SRFX(min)
t
SS
～
～
～
～
～
ACT
10. Clock Suspend Exit & Power Down Exit
11. Auto Refresh & Self Refresh
1) Clock Suspend (=Active Power Down) Exit
2) Power Down (=Precharge Power Down) Exit
CLK
CKE
Internal
CLK
CMD
RD
CLK
CKE
Internal
CLK
CMD
NOP ACT
相關PDF資料
PDF描述
KBJ2501 25A SINGLE PHASE SILICON BRIDGE RECTIFIER
KBJ2502 25A SINGLE PHASE SILICON BRIDGE RECTIFIER
KBJ2503 25A SINGLE PHASE SILICON BRIDGE RECTIFIER
KBJ2504 25A SINGLE PHASE SILICON BRIDGE RECTIFIER
KBJ2505 25A SINGLE PHASE SILICON BRIDGE RECTIFIER
相關代理商/技術參數
參數描述
KB-E100SRW 功能描述:LED 顯示器和配件 Red 640nm 90mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube
KB-E100SURKW 功能描述:LED條和陣列 8.89X3.81MM RED LT BAR LED DISPLAY RoHS:否 制造商:Avago Technologies 產品:LED Light Bars 照明顏色:Red 光強度:45 mcd 封裝:Tube
KBE1A11N 制造商:Lovato Electric Inc 功能描述:
KBEV 5T-0.5-RSSV 4.5T 制造商:TURCK Inc 功能描述:KBEV 5T-0.5-RSSV 4.5T
KB-F100SRW 功能描述:LED 顯示器和配件 Red 640nm 200mcd Diffused Light Bar RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*