- 您現在的位置：買賣IC網 > PDF目錄384578 > KMA210 (NXP Semiconductors N.V.) Programmable angle sensor PDF資料下載
參數資料
| 型號： | KMA210 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 振動和傾斜傳感器 |
| 英文描述： | Programmable angle sensor |
| 封裝： | KMA210<SOT1288|<<<1<Always Pb-free,; |
| 文件頁數： | 7/36頁 |
| 文件大?。?/td> | 563K |
| 代理商： | KMA210 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
KMA210
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 1 — 30 June 2011
7 of 36
NXP Semiconductors
KMA210
Programmable angle sensor
Table 4
describes the power-loss behavior and gives the resulting output voltage
depending on the interrupted supply or ground line and the load resistance.
Table 4.
Load resistance
R
L(ext)
> 5 k
7.4 Broken bond wire detection
The broken bond wire detection circuit enables the detection of an interrupted supply or
ground line of the MR sensor bridge. In the case of a broken bond wire the device goes
into diagnostic mode and a status bit is set.
7.5 Low supply voltage detection and overvoltage protection
If the supply voltage is below the switch-off threshold voltage, a status bit is set and the
device goes into diagnostic mode. If the supply voltage is above the overvoltage switch-on
threshold voltage, the device enters diagnostic mode.
Table 5
describes the system
behavior depending on the voltage range of the supply voltage.
Table 5.
Supply voltage
0 V to
1.8 V
Fig 4.
Equivalent output circuit in case of a power-loss condition
Power-loss behavior
Interrupted supply line
V
O
4 %V
DD
Interrupted ground line
V
O
96 %V
DD
008aaa259
ZO(pl)
ZO(pl)
OUT/DATA
GND
V
DD
KMA210
System behavior
State
start-up power The output buffer drives an active LOW or is powered down,
but the switches of the power-loss detection circuit are not
fully opened and set the output to a level between ground and
half the supply voltage.
1.8 V to V
POR
power-on
reset
switches of the detection circuit off. The output buffer drives
an active LOW and sets the output to the lower diagnostic
level. During the reset phase all circuits are in reset and/or
Power-down mode.
V
POR
to V
th(on)
or
V
th(off)
content of the non-volatile memory is copied into the shadow
registers. The output buffer drives an active LOW and sets the
output to the lower diagnostic level.
V
th(on)
or V
th(off)
to
minimum V
DD
operation
available at the analog output. Not all parameters are within
the specified limits.
Description
The power-loss charge pump is fully operational and turns the
initialization
The digital core and the oscillator are active. After reset the
functional
All analog circuits are active and the measured angle is
相關PDF資料 |
PDF描述 |
|---|---|
| KMI15 | Rotational speed sensor |
| KMI16 | Integrated rotational speed sensor |
| KMI18 | Integrated rotational speed sensor |
| KMZ41 | Magnetic field sensor |
| KMZ43T | Magnetic field sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KMA210-115 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Programmable angle sensor |
| KMA220 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual channel programmable angle sensor |
| KMA220,118 | 制造商:NXP 功能描述:KMA220 Series 5 V Dual Channel Programmable Angle Sensor - SOT-1188-1 |
| KMA220J | 制造商:NXP Semiconductors 功能描述:KMA220/SIL4/REEL13// - Tape and Reel 制造商:NXP Semiconductors 功能描述:MOD ANGLE SENSOR MAGN 2CH SIL4 |
發布緊急采購，3分鐘左右您將得到回復。