- 您現在的位置：買賣IC網 > PDF目錄384587 > L9215A (Lineage Power) Short-Loop Sine Wave Ringing SLIC(短環路正弦波振鈴用戶接口（SLIC）) PDF資料下載
參數資料
| 型號： | L9215A |
| 廠商： | Lineage Power |
| 英文描述： | Short-Loop Sine Wave Ringing SLIC(短環路正弦波振鈴用戶接口（SLIC）) |
| 中文描述： | 短回路正弦波振鈴用戶接口（短環路正弦波振鈴用戶接口電路（SLIC）） |
| 文件頁數： | 4/46頁 |
| 文件大?。?/td> | 1165K |
| 代理商： | L9215A |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Advance Data Sheet
October 2000
Short-Loop Sine Wave Ringing SLIC
L9215A/G
4
Lucent Technologies Inc.
Features
I
On board balanced ringing generation
— 40 Vrms with a 1.414 crest factor provided to 5
REN ring load (1386
+ 40
μ
F) with 100
ring-
ing loop
— 40 Vrms with a 1.414 crest factor provided to 3
REN ring load (2310
+ 24
μ
F) with 250
ring-
ing loop
— No ring relay
— No bulk ring generator required
— 15 Hz to 70 Hz ring frequency supported
— Sine wave input-sine wave output
— PWM input-sine wave output
— Square wave input-trapezoidal output
I
Power supplies requirements
— V
CC
talk battery and ringing battery required
— No –5 V supply required
— No high-voltage positive supply required
I
Flexible Vcc options
— 5 V or 3.3 V V
CC
operation
— 5 V or 3.3 V V
CC
interchangeable and transparent
to users
I
Automatic battery switch
— Minimize off-hook power dissipation
I
Minimal external components required
I
11 operating states
— Forward active, V
BAT2
applied
— Polarity reversal active, V
BAT2
applied
— On-hook transmission, V
BAT1
applied
— On-hook transmission polarity reversal, V
BAT1
applied
— PPM active forward active, V
BAT2
applied
— PPM active polarity reversal active, V
BAT2
applied
— PPM active on-hook transmission, V
BAT1
applied
— PPM active on-hook transmission polarity rever-
sal, V
BAT1
applied
— Scan
— Forward disconnect
— Ring mode
I
Unlatched parallel data control interface
I
Ultralow SLIC power
— Scan 37 mW (V
CC
= 5 V)
— Forward/reverse active 54 mW (V
CC
= 5 V)
— Scan 27 mW (V
CC
= 3.3 V)
— Forward/reverse active 41 mW (V
CC
= 3.3 V)
I
Supervision
— Loop start, fixed threshold with hysteresis
— Ring trip, single-pole ring trip filtering, fixed thresh-
old as a function of battery voltage
— Common-mode current for ground key applica-
tions, user-adjustable threshold
I
Adjustable current limit
— 10 mA to 70 mA programming range
I
Overhead voltage
— Adjustable in active mode
— Clamped <51 V in scan mode
I
Thermal shutdown protection with hysteresis
I
Longitudinal balance
— ETSI/ITU-T balance
—
Telcordia
Technologies
TA-909 balance
I
Meter pulse compatible
— Dedicated meter pulse signal input
— On-hook transmission of PPM
I
ac interface
— Two SLIC gain options to minimize external com-
ponents required for interface to first- or third-gen-
eration codecs
— Sufficient dynamic range for direct coupling to
codec output
I
32-pin PLCC package
I
90 V CBIC-S technology
Description
The L9215 is designed to provide battery feed, ringing,
and supervision functions on short plain old telephone
service (POTS) loops. Supported loop length is 100
to 250
of wiring resistance plus handset or ringing
load. This device is designed for ultralow power in all
operating states.
The L9215 offers 11 operating states. The device
assumes uses of a lower-voltage talk battery, a higher-
voltage ringing battery, and a V
CC
supply.
The L9215 requires only a positive V
CC
supply. No
–5 V supply is needed. The L9215 can operate with a
V
CC
of either 5 V or 3.3 V, allowing for greater user flex-
ibility. The choice of V
CC
voltage is transparent to the
user; the device will function with either supply voltage
connected.
Two batteries are used:
1. A high-voltage ring battery (V
BAT1
).
V
BAT1
is a maximum –75 V. V
BAT1
is used for power
ring signal amplification and for scan and on-hook
transmission modes. This supply is current limited
to approximately the maximum power ringing cur-
rent, typically 50 mA.
2. A lower-voltage talk battery (V
BAT2
).
V
BAT2
is used for active mode powering.
相關PDF資料 |
PDF描述 |
|---|---|
| L9216A | Short-Loop Ringing SLIC with Ground Start(接地起動的短環路振鈴用戶接口) |
| L9216G | Short-Loop Ringing SLIC with Ground Start(接地起動的短環路振鈴用戶接口) |
| L9219A | Low-Cost Line Interface with Reverse Battery and Dual Current Limit(帶反相電池和雙電流限制的低價格線接口) |
| L9219G | Low-Cost Line Interface with Reverse Battery and Dual Current Limit(帶反相電池和雙電流限制的低價格線接口) |
| L9305A | Dual High Current Relay Driver(雙大電流繼電器驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9216A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Short-Loop Ringing SLIC with Ground Start |
| L9217A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| L9218A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| L9219A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| L9222 | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。