參數資料
型號: LCP02-150B1RL
廠商: 意法半導體
英文描述: PROTECTION IC FOR RINGING SLICS
中文描述: 保護IC振鈴SLIC組件
文件頁數: 6/8頁
文件大?。?/td> 72K
代理商: LCP02-150B1RL
LCP02-150B1
6/8
Figure 5 shows the classical protection circuit using the LCP02 crowbar concept. This topology has been
developped to protect the new two-battery voltage SLICs. Itallowsbothpositiveandnegativefiringthresholds
tobeprogrammed.The LCP02-150B1 has two gates (Gn and Gp). Gn is biased to negative battery voltage
-Vbat, while Gp is biased to the positive battery voltage +Vb.
When a negative surge occurs on one wire (L1 for example), a current Ign flows through the base of the
transistor T1 and then injects a current in the gate of the thyristor Th1 which fires. All the surge current
flows through the ground. After the surge, when the current flowing through Th1 becomes less negative
than the negative holding current Ih-, Th1 switches off. This holding current I
H-
is temperature dependant
as per figure2.
When a positive surge occurs on one wire (L1 for example), a current Igp flows through the base of the
transistor T2 and then injects a current in the gate of the thyristor Th2 which fires. All the surge current
flows through the ground. After the surge, when the current flowing through Th2 becomes less positive
than the positive holding current Ih+, Th2 switches off. This holding current I
H+
, typically 20mA at 25°C, is
temperature dependant and the same figure 2 also applies.
The capacitors Cn and Cp are used to speed up the crowbar structure firing during the fast rise or fall
edges.ThisallowstominimizethedynamicalbreakovervoltageattheSLICTipandRinginputsduringfast
surges. Please note that these capacitors are generally available around the SLIC. To be efficient they
have to be as close as possible to the LCP02-150B1 gate pins (Gn and Gp) and to the reference ground
track (or plan). The optimized value for Cn and Cp is 220nF.
The series resistors Rs1 and Rs2 designed in figure 5 represent the fuse resistors or the PTCs which are
needed to withstand the power contact or the power induction tests imposed by the country standards.
Taking this factor into account, the actual lightning surge current flowing through the LCP02-150B1 is
equal to :
I surge = Vsurge / (Rg + Rs)
With
V surge = peak surge voltage imposed by the standard.
Rg = series resistor of the surge generator
Rs = series resistor of the line card (e.g. PTC)
e.g.: Foralinecardwith50
ofseriesresistorswhichhastobequalifiedunderBellcore1000V10/1000μs
surge, the present current through the LCP02-150B1 is equal to :
I surge = 1000 / (10 + 50) =
17A
TECHNICAL INFORMATION
Cp
Gn
TIP
RING
Gp
GND
-Vbat
+Vb
Cn
Rs1
Rs2
L 1
L 2
GND
VTip
Th1
Th2
T1
T2
Ign
Igp
V Ring
Fig. 5:
LCP02 concept behavior.
相關PDF資料
PDF描述
LCP02-150B1 PROTECTION IC FOR RINGING SLICS
LCP02-150M PROGRAMMABLE TRANSIENT VOLTAGE SUPPRESSOR FOR RINGING SLICS
LCP02-150M-TR PROGRAMMABLE TRANSIENT VOLTAGE SUPPRESSOR FOR RINGING SLICS
LCZM 16-/14-/12-Bit VOUT DACs in 3mm 】 3mm DFN
LCZN 16-/14-/12-Bit VOUT DACs in 3mm 】 3mm DFN
相關代理商/技術參數
參數描述
LCP02-150M 功能描述:TVS二極管陣列 Programmable TVS RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C
LCP02-150M-TR 功能描述:TVS二極管陣列 Programmable TVS RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C
LCP-04 制造商:JST Manufacturing 功能描述:HOUSING Bulk 制造商:JST Manufacturing 功能描述:HOUSING; Connector Type:Wire to Board; Series:LC; Contact Termination:Crimp; Gender:Receptacle; No. of Contacts:4; No. of Rows:1; Pitch Spacing:5.08mm; Contact Plating:Tin; Contact Material:Brass; SVHC:No SVHC (19-Dec-2012); ;RoHS Compliant: Yes
LC-P0612P 功能描述:密封鉛酸電池 6V 12AH .187" TABS RoHS:否 制造商:CSB 輸出電壓:12 V 容量: 大小: 端接類型:Faston Tab
LC-P067R2P 功能描述:密封鉛酸電池 6V 7.2AH .187" TABS RoHS:否 制造商:CSB 輸出電壓:12 V 容量: 大小: 端接類型:Faston Tab