- 您現在的位置：買賣IC網 > PDF目錄65797 > LV8098CS (SANYO SEMICONDUCTOR CO LTD) VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 PDF資料下載
參數資料
| 型號： | LV8098CS |
| 廠商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分類： | 運動控制電子 |
| 英文描述： | VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 |
| 封裝： | 1.27 X 0.87 MM, 0.50 MM HEIGHT, WLP-6 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 222K |
| 代理商： | LV8098CS |
LV8098CS
I
2C bus transmission method
Start and stop conditions
The I
2C bus requires that the state of SDA be preserved while SCL is high as shown in the timing diagram below during a
data transfer operation.
ts2
th2
SCL
SDA
When data is not being transferred, both SCL and SDA are in the high state. The start condition is generated and access is
started when SDA is changed from high to low while SCL and SDA are high.
Conversely, the stop condition is generated and access is ended when SDA is changed from low to high while SCL is
high.
th1
th3
SCL
SDA
Start condition
Stop condition
Data transfer and acknowledgement response
After the start condition has been generated, the data is transferred one byte (8 bits) at a time. Generally, in an I
2C bus, a
unique 7-bit slave address is assigned to each device, and the first byte of the transfer data is allocated to the 7-bit slave
address and to the command (R/W) indicating the transfer direction of the subsequent data. However, this IC is provided
with only a write mode for receiving the data. Every time 8 bits of data for each byte are transferred, the ACK signal is
sent from the receiving end to the sending end. Immediately after the clock pulse of SCL bit 8 in the data transferred has
fallen to low, SDA at the sending end is released, and SDA is set to low at the receiving end, causing the ACK signal to be
sent. When, after the receiving end has sent the ACK signal, the transfer of the next byte remains in the receiving status,
the receiving end releases SDA at the falling edge of the ninth SCL clock.
M
S
B
L
S
B
A
C
K
L
S
B
A
C
K
M
S
B
M
S
B
L
S
B
A
C
K
W
Data
X : DON'T CARE
A1
SCL
SDA
(WRITE)
Data
Slave address
2nd byte
3ed byte
1st byte
Start
Stop
A2 A3 A4 A5 A6 A7 0
PD X D7D6D5D4D3D2
D1 D0 XXXXXX
No.A1515-6/8
相關PDF資料 |
PDF描述 |
|---|---|
| LV8098CS | VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 |
| LV8406T | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO20 |
| LV8413GP | BRUSH DC MOTOR CONTROLLER, 0.6 A, QCC16 |
| LV8413GP | BRUSH DC MOTOR CONTROLLER, QCC16 |
| LV8804FV | AC MOTOR CONTROLLER, 1.2 A, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LV8099CS | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Constant-current Driver IC |
| LV8099CS-TE-L-H | 制造商:ON Semiconductor 功能描述:VOICE COIL MOTOR DRIVER - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述:REEL / VOICE COIL MOTOR DRIVER 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LV8099CT | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For VCMs Constant-current Driver IC |
| LV8099CT-TE-L-H | 功能描述:IC MOTOR DRIVER S111 WLP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:* 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LV8104V | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:For Variable Speed Control Three-Phase Brushless Motor Predriver |
發布緊急采購，3分鐘左右您將得到回復。