- 您現在的位置：買賣IC網 > PDF目錄359129 > MAX809JD (NXP SEMICONDUCTORS) 3-pin microprocessor resets PDF資料下載
參數資料
| 型號： | MAX809JD |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 電源管理 |
| 英文描述： | 3-pin microprocessor resets |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| 封裝： | 1.50 MM, PLASTIC, SOT-23, SOP-3 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 98K |
| 代理商： | MAX809JD |
Philips Semiconductors
Product data
MAX809/MAX810
3-pin microprocessor resets
2003 Aug 08
7
APPLICATION INFORMATION
Detailed description
A microprocessor reset ensures that the microprocessor starts in a
known and safe state. The reset asserts a reset signal to prevent
code execution errors during power up, power down, or brownout
conditions.
A reset must assert an output within a predictable range of the
supply voltage. The common threshold voltage range is between 5%
and 10% of the nominal supply voltage. MAX809/MAX810 have
4.63 V, 3.08 V and 2.63 V options for 5 V, 3.3 V and 3.0 V supplies
respectively. They have high accuracy (within
±
3%) that ensures
that the reset thresholds occur within the safe operating range.
Whenever the supply voltage falls below the reset threshold, the
reset signal is asserted. It remains asserted for at least 140 ms after
the supply voltage rises above the threshold. At this point the reset
is released. This delay time helps ensure valid reset signals despite
erratic changes in supply voltage. The MAX809/MAX810 have a
push-pull output stage and do not require a pull-up resistor.
Negative-going V
CC
transients
The MAX809/MAX810 are relatively immune to short negative-going
V
CC
transients and glitches. Figure 5 shows the maximum pulse
width a negative-going transient can have without causing a reset
signal. As the magnitude of the transient increases below the reset
threshold, the maximum allowable pulse width decreases. Typically,
for the 4.0 V, 4.38 V, and 4.63 V versions of the MAX809/MAX810, a
V
CC
transient that goes 100 mV below the reset threshold and lasts
20
μ
s or less will not cause a reset signal. To provide additional
transient rejection, connect a 10 nF bypass capacitor as close as
possible to the V
CC
pin.
SL01728
RESET COMPARATOR OVERDRIVE, V
th
– V
CC
(mV)
M
μ
0
50
100
150
200
250
300
350
400
450
1
10
100
1000
MAX809/
MAX810R/S/T/Z
MAX809/MAX810J/L/M
Figure 5. Maximum transient duration without causing a
reset pulse versus reset comparator overdrive.
Ensuring a valid reset output down to V
CC
= 0 V
When V
CC
falls below 1 V, the MAX809 RESET no longer sinks
current (i.e., it becomes open circuit). A high impedance CMOS
logic input connected to RESET can drift to undetermined voltages.
In most applications in which the microprocessor circuitry is
inoperative below 1 V, this will not represent a problem. However, in
applications in which RESET must be valid down to 0 V, use a
relatively large resistor from RESET to ground as shown in Figure 6.
100 k
is small enough to provide a path for any leakage currents to
flow to ground (holding RESET LOW); while it is large enough not to
load RESET. Conversely, a 100 k
pull-up resistor is recommended
for MAX810 if RESET is required to remain valid for V
CC
< 1 V.
V
CC
V
CC
V
CC
GND
GND
RESET
RESET
SL01726
MAX809
MICROPROCESSOR
100 k
Figure 6. RESET valid to V
CC
= 0 V circuit.
Interfacing to microprocessors with bi-directional
reset pins
Microprocessors with bi-directional reset I/Os, such as the Motorola
68HC11 series, can be connected to the MAX809 RESET output. To
ensure a correct output on the MAX809, even when the
microprocessor reset I/O is in the opposite state, connect a 4.7 k
resistor between the reset pins as shown in Figure 7. This allows the
microprocessor to issue commands to the system regardless of the
state of the RESET. The bi-directional microprocessor reset
functions both as a driven reset input and as an active reset driver.
V
CC
V
CC
V
CC
GND
GND
SL01727
MAX809
MOTOROLA
68HCxx
4.7 k
RESET
RESET
Figure 7. Interfacing to microprocessor with bi-directional
reset I/O
相關PDF資料 |
PDF描述 |
|---|---|
| MAZY047(MA1Z047) | 小信號デバイス － ダイオード － ツェナーダイオード |
| MAZY510(MA1Z510) | 小信號デバイス － ダイオード － ツェナーダイオード |
| MAZY180(MA1Z180) | 小信號デバイス － ダイオード － ツェナーダイオード |
| MAZY150(MA1Z150) | 小信號デバイス － ダイオード － ツェナーダイオード |
| MAZY110(MA1Z110) | 小信號デバイス － ダイオード － ツェナーダイオード |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX809JEUR | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX809JEUR+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4V 3PIN SOT-23 - Rail/Tube |
| MAX809JEUR+T | 功能描述:監控電路 3-Pin MPU Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX809JEUR+T10 | 功能描述:監控電路 NULL RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX809JEUR-T | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。