- 您現在的位置：買賣IC網 > PDF目錄16290 > MAX9597EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX9597 PDF資料下載
參數資料
| 型號： | MAX9597EVKIT+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 9/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL FOR MAX9597 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 主要目的： | SCART 接口 |
| 已用 IC / 零件： | MAX9597 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
MAX9597
Low-Power Audio/Video Interface
for Single SCART Connectors
______________________________________________________________________________________
17
Conditions section). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
SDA and SCL idle high when the bus is not in use. A
master initiates communication by issuing a START con-
dition. A START condition is a high-to-low transition on
SDA with SCL high. A STOP condition is a low-to-high
transition on SDA while SCL is high (Figure 5). A START
condition from the master signals the beginning of a
transmission to the MAX9597. The master terminates
transmission, and frees the bus, by issuing a STOP con-
dition. The bus remains active if a REPEATED START
condition is generated instead of a STOP condition.
Early STOP Conditions
The MAX9597 recognizes a STOP condition at any
point during data transmission except if the STOP con-
dition occurs in the same high pulse as a START condi-
tion. For proper operation, do not send a STOP
condition during the same SCL high pulse as the
START condition.
Slave Address
The slave address is defined as the 7 most significant
bits (MSBs) followed by the read/write (R/W) bit. Set the
R/W bit to 1 to configure the MAX9597 to read mode.
Set the R/W bit to 0 to configure the MAX9597 to write
mode. The slave address is always the first byte of
information sent to the MAX9597 after a START or a
REPEATED START condition. The MAX9597 slave
address is configurable with DEV_ADDR. Table 3
shows the possible slave addresses for the MAX9597.
Acknowledge
The acknowledge bit (ACK) is a clocked 9th bit that the
MAX9597 uses to handshake receipt of each byte of
data when in write mode (see Figure 6). The MAX9597
pulls down SDA during the entire master-generated
ninth clock pulse if the previous byte is successfully
received. Monitoring ACK allows for detection of unsuc-
cessful data transfers. An unsuccessful data transfer
occurs if a receiving device is busy or if a system fault
has occurred. In the event of an unsuccessful data
transfer, the bus master may retry communication. The
master pulls down SDA during the ninth clock cycle to
acknowledge receipt of data when the MAX9597 is in
read mode. An acknowledge is sent by the master after
each read byte to allow data transfer to continue. A not
acknowledge is sent when the master reads the final
byte of data from the MAX9597, followed by a STOP
condition.
Write Data Format
A write to the MAX9597 consists of transmitting a
START condition, the slave address with the R/W bit set
to 0, one data byte to configure the internal register
address pointer, one or more data bytes, and a STOP
condition. Figure 7 illustrates the proper frame format
for writing one byte of data to the MAX9597. Figure 8
illustrates the frame format for writing n-bytes of data to
the MAX9597.
The slave address with the R/W bit set to 0 indicates
that the master intends to write data to the MAX9597.
The MAX9597 acknowledges receipt of the address
byte during the master-generated ninth SCL pulse.
The second byte transmitted from the master config-
ures the MAX9597’s internal register address pointer.
The pointer tells the MAX9597 where to write the next
byte of data. An acknowledge pulse is sent by the
MAX9597 upon receipt of the address pointer data.
The third byte sent to the MAX9597 contains the data
that is written to the chosen register. An acknowledge
pulse from the MAX9597 signals receipt of the data
byte. The address pointer autoincrements to the next
SCL
SDA
SSr
P
Figure 5. START, STOP, and REPEATED START Conditions
1
SCL
START
CONDITION
SDA
28
9
CLOCK PULSE FOR
ACKNOWLEDGMENT
ACKNOWLEDGE
NOT ACKNOWLEDGE
Figure 6. Acknowledge
相關PDF資料 |
PDF描述 |
|---|---|
| A3DKB-2036M | IDC CABLE - AKR20B/AE20M/APK20B |
| A3BRB-1436M | IDC CABLE - ASR14B/AE14M/APR14B |
| A3AKB-2606M | IDC CABLE - ASC26B/AE26M/APK26B |
| REC3.5-2424SRW/R10/C | CONV DC/DC 3.5W 18-36VIN 24VOUT |
| 7-6278032-6 | C/A MT-RJ/MT-RJ MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9597EVKIT+ | 功能描述:視頻 IC 開發工具 MAX9597 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Evaluation Boards 類型:YPbPr to RGBHV Converters 工具用于評估:LMH1251 工作電源電壓:5 V |
| MAX9598CTL+ | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598CTL+T | 功能描述:視頻開關 IC A/V Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻（最大值）:12 Ohms 傳播延遲時間: 開啟時間（最大值）: 關閉時間（最大值）: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel |
| MAX9598EVKIT+ | 功能描述:交換機 IC 開發工具 MAX9598 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX9600EUP | 功能描述:校驗器 IC Dual ECL-D/Q PECL 500ps Comparator RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。