參數資料
型號： MO15E*TFT-LCD
英文描述： Monitor_ICs:7SZ14 GS1881 MASCOTV NT7181 NT68F63 524C80D81 QZX363C5V6
中文描述： Monitor_ICs：7SZ14 GS1881 MASCOTV NT7181 NT68F63 524C80D81 QZX363C5V6
文件頁數： 2/39頁
文件大?。?/td> 728K
1-1-1 Warnings
1.
For continued safety, do not attempt to modify the
circuit board.
Disconnect the AC power and DC Power Jack
before servicing.
When the chassis is operating, semiconductor
heatsinks are potential shock hazards.
2.
3.
1-1-2 Servicing the LCD Monitor
1. When servicing the LCD Monitor, remove the static
charge by connecting a 10k ohm resistor in series
with an insulated wire (such as a test probe)
between the chassis and the anode lead.
(Disconnect the AC line cord from the AC outlet.)
2.
It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.
1-1-3 Fire and Shock Hazard
Before returning the monitor to the user, perform the
following safety checks:
1.
Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.
2.
Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3.
Leakage Current Hot Check (Figure 1-1):
WARNING: Do not use an isolation transformer during
this test.
Use a leakage current tester or a metering system
that complies with American National Standards
Institute (
ANSI C101.1, Leakage Current for
Appliances
), and Underwriters Laboratories (
UL
Publication UL1410, 59.7
).
Figure 1-1. Leakage Current Test Circuit
4.
With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat
the test.
1-1-4 Product Safety Notices
Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by
on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.
MO15E*
1-1
CONFIDENTIAL
1 Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1 Safety Precautions
DEVICE
UNDER
TEST
TEST ALL
EXPOSED METAL
SURFACES
(READING SHOULD
NOT BE ABOVE 0.5mA)
LEAKAGE
CURRENT
TESTER
2-WIRE CORD
ALSO TEST WITH
PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)
EARTH
GROUND
!
相關PDF資料
PDF描述
MO241A 0.4 DUAL DIGIT NUMERIC DISPLAYS
MO245A 0.4 DUAL DIGIT NUMERIC DISPLAYS
MO251A 0.5 DUAL DIGIT NUMERIC DISPLAYS
MO356A 0.56 THREE DIGIT NUMERIC DISPLAYS
MO433FA 0.33, 4 DIGIT NUMERIC DISPLAY
相關代理商/技術參數
參數描述
MO18-1004-25.000M 制造商:IMPACT 功能描述:
MO1812 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Plastic Moulded Inductor High L
MO1812-101M 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Plastic Moulded Inductor High L
MO1812-102K 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Plastic Moulded Inductor High L
MO1812-103K 制造商:PREMO 制造商全稱:PREMO CORPORATION S.L 功能描述:Plastic Moulded Inductor High L
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*