- 您現在的位置：買賣IC網 > PDF目錄299768 > PF38F40L0YUQ0 (NUMONYX) 16M X 16 FLASH 1.8V PROM, PBGA88 PDF資料下載
參數資料
| 型號： | PF38F40L0YUQ0 |
| 廠商： | NUMONYX |
| 元件分類： | PROM |
| 英文描述： | 16M X 16 FLASH 1.8V PROM, PBGA88 |
| 封裝： | 8 X 11 MM, 1 MM HEIGHT, ROHS COMPLIANT, VFBGA-88 |
| 文件頁數： | 35/99頁 |
| 文件大小： | 1419K |
| 代理商： | PF38F40L0YUQ0 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
Intel StrataFlash Wireless Memory (L18)
Intel StrataFlash Wireless Memory (L18) with A/D-Multiplexed I/O
Datasheet
July 2006
40
Order Number: 313295-002US
9.1.4
Standby
When CE# is deasserted the device is deselected and placed in standby, substantially
reducing power consumption. In standby, the data outputs are placed in High-Z,
independent of the level placed on OE#. Standby current, ICCS, is the average current
measured over any 5 ms time interval, 5 μs after CE# is deasserted. During standby,
average current is measured over the same time interval 5 μs after CE# is deasserted.
When the device is deselected (while CE# is deasserted) during a program or erase
operation, it continues to consume active power until the program or erase operation is
completed.
9.1.5
Reset
As with any automated device, it is important to assert RST# when the system is reset.
When the system comes out of reset, the system processor attempts to read from the
flash memory if it is the system boot device. If a CPU reset occurs with no flash
memory reset, improper CPU initialization may occur because the flash memory may
be providing status information rather than array data. Intel flash memories allow
proper CPU initialization following a system reset through the use of the RST# input.
RST# should be controlled by the same low-true reset signal that resets the system
CPU.
After initial power-up or reset, the device defaults to asynchronous Read Array, and the
Status Register is set to 0x80. Asserting RST# de-energizes all internal circuits, and
places the output drivers in High-Z. When RST# is asserted, the device shuts down the
operation in progress, a process which takes a minimum amount of time to complete.
When RST# has been deasserted, the device is reset to asynchronous Read Array
state.
Note:
If RST# is asserted during a program or erase operation, the operation is terminated
and the memory contents at the aborted location (for a program) or block (for an
erase) are no longer valid, because the data may have been only partially written or
erased.
When returning from a reset (RST# deasserted), a minimum wait is required before the
initial read access outputs valid data. Also, a minimum delay is required after a reset
before a write cycle can be initiated. After this wake-up interval passes, normal
operation is restored. See Section 7.0, “AC Characteristics” on page 22 for details
about signal-timing.
9.2
Device Commands
Device operations are initiated by writing specific device commands to the Command
User Interface (CUI). See Table 13, “Command Bus Cycles” on page 41.
Several commands are used to modify array data including Word Program and Block
Erase commands. Writing either command to the CUI initiates a sequence of internally-
timed functions that culminate in the completion of the requested task. However, the
operation can be aborted by either asserting RST# or by issuing an appropriate
suspend command.
相關PDF資料 |
PDF描述 |
|---|---|
| PF50WIW2K-3.5VF-W6 | SINGLE COLOR LED, INCAND WHITE |
| PD50WO3K-28V-T | SINGLE COLOR LED, SUPER ORANGE |
| PD50WR3K-24V-W6 | SINGLE COLOR LED, ULTRA RED |
| PF50WAG6K-240VAC-W6 | SINGLE COLOR LED, AQUA GREEN |
| PF50WW1K-12V-W6 | SINGLE COLOR LED, COOL WHITE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PF38F4470LLYBBEA | 制造商:Micron Technology Inc 功能描述:256LCR/256LCR/256SD SCSP 1.8 X16D LF - Trays |
| PF38F5050M0Y0CFA | 制造商:Micron Technology Inc 功能描述:512BA/64PS SCSP 1.8 LF MICRON - Trays |
| PF38F5050M0Y0CFB | 制造商:Micron Technology Inc 功能描述:512BA/64PS SCSP 1.8 LF MICRON - Tape and Reel |
| PF38F5050M0Y0CGA | 制造商:Micron Technology Inc 功能描述:512BA/64PS SCSP 1.8 LF MICRON - Trays |
| PF38F5060M0Y0BEA | 功能描述:IC FLASH 512MBIT 133MHZ 105SCSP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:3,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K (4K x 8) 速度:100kHz，400kHz 接口:I²C，2 線串口 電源電壓:2.5 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) 其它名稱:CAV24C32WE-GT3OSTR |
發布緊急采購，3分鐘左右您將得到回復。