參數資料
型號： PSD413A1-15UI
英文描述： Field-Programmable Peripheral
中文描述： 現場可編程外圍
文件頁數： 64/123頁
文件大?。?/td> 657K
代理商： PSD413A1-15UI
PSD4XX Famly
61
9.4 Memory Block
The PSD4XX provides EPROM memory for code storage and SRAM memory for scratch
pad usage. Chip selects for the memory blocks come from the DPLD decoding logic and
are defined by the user in the PSDsoft Software. Figure 32 shows the organization of the
Memory Block.
The PSD4XX family uses Zero-power memory techniques that place memory into Standby
Mode between MCU accesses. The memory becomes active briefly after an address
transition, then delivers new data to the outputs, latches the outputs, and returns to standby.
This is done automatically and the designer has to do nothing special to benefit from this
feature. Both the EPROM and SRAM have this feature.
9.4.1 EPROM
The PSD4XX provides three EPROM densities: 256Kbit, 512Kbit, or 1Mbit. The EPROM
is divided into four 8K, 16K or 32K byte blocks. Each block has its own chip select signals
(ES0 – ES3). The EPROM can be configured as 32K x 8, 64K x 8 or 128K x 8 for
microcontrollers with an 8-bit data bus. For 16-bit data buses, the EPROM is configured as
16K x 16, 32K x 16 or 64K x 16.
9.4.2 SRAM
The SRAM has 16Kbits of memory, organized as 2K x 8 or 1K x 16. The SRAM is enabled
by chip select signal RS0 from the DPLD. The SRAM has a battery back-up (STBY) mode.
This back-up mode is invoked when the V
CC
voltage drops under the Vstdby voltage by
approximately 0.7 V. The Vstdby voltage is connected only to the SRAM and cannot be
lower than 2.7 volts.
9.4.3 Memory Select Map
The EPROM and SRAM chip select equations are defined in the ABEL file in terms of
address and other DPLD inputs. The memory space for the EPROM chip select
(ES0 – ES3) should not be larger than the EPROM block (8KB, 16KB, or 32KB) it is
selecting.
The following rules govern how the internal PSD4XX memory selects/space are defined:
J
The EPROM blocks address space cannot overlap
J
SRAM, internal I/O and Peripheral I/O space cannot overlap
J
SRAM, internal I/O and Peripheral I/O space can overlap EPROM space, with
priority given to SRAM or I/O. The portion of EPROM which is overlapped
cannot be accessed.
The Peripheral I/O space refers to memory space occupied by peripherals when Port A is
configured in the Peripheral I/O Mode.
The PSD4XX
Architecture
(cont.)
相關PDF資料
PDF描述
PSD413A1-20J 400V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a TO-205AF package; A IRHF7330SE with Standard Packaging
PSD413A1-20JI Field-Programmable Peripheral
PSD413A1-20LI -200V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a TO-254AA package; A IRHMS597260 with Standard Packaging
PSD413A1-20LM -100V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-0.5 package; Similar to IRHNJ9130 with optional Total Dose Rating of 300kRads
PSD413A1-20U -60V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a Low-Ohmic TO-257AA package; Similar to IRHYS597034CM with optional Total Dose Rating of 300kRads
相關代理商/技術參數
參數描述
PSD413A2-C-70L 制造商:WSI 功能描述:
PSD4-16 制造商:Tamura Corporation of America 功能描述:
PSD4-20 制造商:MICROTRAN 功能描述:POWER TRANSFORMER, 6 VA
PSD4235G2-70U 功能描述:SPLD - 簡單可編程邏輯器件 5.0V 4M 70ns RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池?cái)?shù)量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24
PSD4235G2-90U 功能描述:CPLD - 復雜可編程邏輯器件 5.0V 4M 90ns RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*