參數資料
型號： QBW018A0B61
元件分類： 電源模塊
英文描述： 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封裝： ROHS COMPLIANT PACKAGE-7
文件頁數： 16/17頁
文件大小： 303K
代理商： QBW018A0B61
Data Sheet
December 7, 2007
QBW018A0B Series Power Modules, DC - DC Converters:
36 – 75Vdc Input; 12Vdc Output; 18A Output Current
8
Tyco Electronics Power Systems
Test Configurations
Note: Measure input reflected-ripple current with a simulated
source inductance (LTEST) of 12 H. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
Figure 9. Input Reflected Ripple Current Test
Setup.
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
VO(+)
COM
1uF .
RESISTIVE
LOAD
SCOPE
COPPER STRIP
GROUND PLANE
10uF
Figure 10. Output Ripple and Noise Test Setup.
VO
COM
VIN(+)
COM
RLOAD
Rcontact
Rdistribution
Rcontact
Rdistribution
Rcontact
Rdistribution
VIN
VO
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 11. Output Voltage and Efficiency Test
Setup.
η =
VO.IO
VIN.IIN
x 100 %
Efficiency
Design Considerations
Input Filtering
The power module should be connected to a low
ac-impedance source. A highly inductive source
impedance can affect the stability of the power
module. For the test configuration in Figure 9, a
100μF electrolytic capacitor (ESR<0.7
Ω at 100kHz),
mounted close to the power module helps ensure the
stability of the unit. Consult the factory for further
application guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and
separation requirements of the end-use safety agency
standard, i.e., UL 1950, CSA C22.2 No. 60950-00,
and VDE 0805:2001-12 (IEC60950 3
rd Ed).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75Vdc), for the module’s output to be considered as
meeting the requirements for safety extra-low voltage
(SELV), all of the following must be true:
The input source is to be provided with reinforced
insulation from any other hazardous voltages,
including the ac mains.
One VIN pin and one VOUT pin are to be
grounded, or both the input and output pins are
to be kept floating.
The input pins of the module are not operator
accessible.
Another SELV reliability test is conducted on the
whole system (combination of supply source and
subject module), as required by the safety
agencies, to verify that under a single fault,
hazardous voltages do not appear at the
module’s output.
Note:
Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV)
outputs when all inputs are ELV. The input to these
units is to be provided with a maximum 15 A fast-
acting (or time-delay) fuse in the unearthed lead.
相關PDF資料
PDF描述
QDF-2T1-4 INTERCONNECTION DEVICE
QDF-2TP-5 INTERCONNECTION DEVICE
QDSP-399G-00000 7 SEG NUMERIC DISPLAY, GREEN, 10 mm
QEB421.TR 2.4 mm, 1 ELEMENT, INFRARED LED, 880 nm
QEHC49H3310HM5016 HC49/S Crystal - Through Hole packaged
相關代理商/技術參數
參數描述
QBW018A0B61-HTZ 功能描述:DC/DC轉換器 36-75Vin 12Vout 18A Neg TH Pin 3.68mm BP RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
QBW018A0B61Z 制造商:LINEAGEPOWER 制造商全稱:LINEAGEPOWER 功能描述:36-75Vdc Input; 12Vdc Output; 18A Output Current
QBW018A0B641 功能描述:DC/DC轉換器 TH 18A, IN 48V OUT 12V,PIN/AUTO/NEG RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
QBW018A0B641Z 功能描述:DC/DC轉換器 18A 7-Pin QRT-Brick RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
QBW018A0B6Z 功能描述:DC/DC轉換器 48Vin 12Vout 18A TH 3.68pin RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*