- 您現在的位置：買賣IC網 > PDF目錄299801 > QPO-1Q (Vicor Corporation) Output Ripple Attenuation SiP PDF資料下載
參數資料
| 型號： | QPO-1Q |
| 廠商： | Vicor Corporation |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Output Ripple Attenuation SiP |
| 中文描述： | 輸出紋波衰減的SiP |
| 文件頁數： | 2/8頁 |
| 文件大小： | 144K |
| 代理商： | QPO-1Q |
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
QPO-1 Data Sheet
Page 2 of 8
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
QPO-1 SiP SPECIFICATIONS (-20°C to +100°C PCB Substrate temperature)
Electrical Characteristics
Electrical characteristics apply over the full operating range of input voltage, output power and PCB substrate temperature, unless
otherwise specified. All temperatures refer to the operating temperature at the interface of the PCB surface with proper reflow mounting of
QPO-1. The PCB surface must have sufficient area and heat via’s to the opposite side to achieve the optimum thermal resistance.
QPO-1 Output
RHR Value (ohms)
3.0V
20k
5.0V
33.3k
12.0V
80k
15.0V
100k
24.0V
160k
28.0V
187k
Table 1—RHR computed values for VHR = 375mV @100mA.
Parameter
Min
Max
Unit
Notes
Operating current range
0.03
10
A
There is no internal current limiting. The system must
be properly fused such that the current does not exceed
the absolute maximum rating of 15A. A minimum
current of 30mA is needed to maintain regulation.
Operating input voltage
3.0
30
Vdc
Continuous
Transient output response
Step load change rates <1A/s
@ 2A step
50
mVp-p
VHR=375mV @ 100mA, Input capacitance = 200F
@ 10A step
50
mVp-p
VHR=375mV @ 100mA, Input capacitance = 1500F
VHR headroom voltage range
(1)
225
525
mV
@ 100mA load with 100mVp-p ripple.
See Table 1 for headroom setting RHR resistor values.
QPOOUT +VHR must be set below converter over voltage trip.
Output noise
10
mVp-p
Input PARD = 100mVp-p, 50Hz-500kHz
5
mVrms
SC output current accuracy(2)
±1
%
See Note 2 and Figure 2 for setting RSS value
ISC=VHR / RSS
QPO-1 bias current
60
mA
Power dissipation
4.0
W
QPOOUT = 28V; Iout = 10A
VHR = 375mV @ 100mA
(without slope adjust or peak detection.)
(1) Headroom voltage, peak detection and slope adjustment must be chosen by the user based on attenuation and efficiency requirements.
The functional description section explains how to optimize the configuration of the QPO-1 for the voltage source used. The headroom
voltage is the difference between the input and the output of the QPO-1 and is set by the selection of resistor RHR.
Calculate RHR as shown.
RHR = (QPOOUT / VHR) x 2.5k (see Table 1 for example values)
(2) RSS resistor sets the correction current required to trim the source output up to accommodate the headroom of the QPO-1 when remote
sense is not used. This function will accommodate power supplies with positive reference based trim configuration.
RSS = RIN * VOUT / VRPT ( If a converter is trimmed down use the resulting VOUT voltage in the formula for RSS)
Where:
RIN = input resistance of the SC or Trim pin;
VOUT = source output voltage;
VRPT = SC or Trim pin pre-trimmed reference
相關PDF資料 |
PDF描述 |
|---|---|
| QPO-2EVAL1 | Evaluation Board for QPO-2 Active Output Filter |
| QPO-2L | QPO-2L Low Voltage Output Ripple Attenuator |
| QS54FCT2240ATZB | FCT SERIES, DUAL 4-BIT DRIVER, INVERTED OUTPUT, PZIP20 |
| QS54FCT2240TZB | FCT SERIES, DUAL 4-BIT DRIVER, INVERTED OUTPUT, PZIP20 |
| QS74FCT2244CTZ | FCT SERIES, DUAL 4-BIT DRIVER, TRUE OUTPUT, PZIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QPO-2EVAL1 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Evaluation Board for QPO-2 Active Output Filter |
| QPO-2-EVAL1 | 功能描述:EVALUATION BOARD FOR QPO-2 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Picor®, QUIETPOWER® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| QPO-2L | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:OUTPUT RIPPLE ATTENUATOR |
| QPO-2LZ | 功能描述:0.3-5.5V 20A OUT RIP ATTENUATOR RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| QPO-2LZ-01 | 功能描述:IC INTERFACE FILTER RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。