- 您現在的位置：買賣IC網 > PDF目錄299801 > QPO-1Q (Vicor Corporation) Output Ripple Attenuation SiP PDF資料下載
參數資料
| 型號： | QPO-1Q |
| 廠商： | Vicor Corporation |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Output Ripple Attenuation SiP |
| 中文描述： | 輸出紋波衰減的SiP |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 144K |
| 代理商： | QPO-1Q |
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715
QPO-1 Data Sheet
Page 4 of 8
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
The product can be used with voltage sources from 3 to 30Vdc
by using either the remote sense or the voltage trim feature.
The two different circuit schematics are shown in Figures 1 and
2. For either configuration, the source output will increase to
accommodate the headroom setting of the QPO-1 filter to
maintain the load voltage at the required level.
The user can optimize performance by setting the low current
(100mA) headroom operating point per Table 1 or by using the
formulas in Notes 1 and 2 above the table. The user must be
aware of the sources over-voltage set-point and not create a
headroom voltage that will cause a shutdown condition. For this
reason it is recommended that the QPO-1 be used with power
supplies running at their factory preset voltages or in a trimmed
down configuration.
In low voltage applications (<12V), it may be required to use the
CSC capacitor. This creates a soft starting of the source
preventing the output from tripping the over voltage function
while the QPO-1 output line comes up to the set-point. The CSC
value will be converter dependent but is typically around 5 to
22F. Remote sensing may also require Qp for start up, use a
logic level low voltage PFET such as IRLML6401 or equivalent.
The spice simulation Figures 5, 6, and 7 demonstrate the effects
of headroom versus attenuation for 3.3, 15, and 28V respectively.
The attenuation and power dissipation will decrease with
headroom setting so a trade-off can be selected for efficiency
versus attenuation. The transient performance is proportional to
the headroom setting, power source response time and the
capacitance present at the input to the QPO-1. The capacitance
may be within the power supply that is used or supplemented by
external capacitance. Consideration of the source’s sensitivity to
additional output capacitance and stability must be understood
before additional capacitance is added for enhancement of
transient performance.
The QPO-1 has two additional features that the user can select to
further optimize performance. The first is a headroom slope
adjustment that reduces the headroom voltage drop with
increasing load current. The second is a peak detector function
that increases the headroom voltage by the peak of the ripple
voltage.
Headroom Slope Adjustment
This can be used to allow for more headroom and improved
transient response at lower loads and also to approximate
constant power dissipation over the load range. The slope of this
curve is set by the slope adjust resistor RSA. See below for setting
the RSA value. The headroom in Figures 5, 6, and 7 are at 10A
and have been reduced by 150mV from the low current
headroom setting with the slope function using an RSA value of
8.2k
. This feature is useful to improve efficiency when used
with converters that have decreasing ripple with increasing load
current such as is typical with Vicor products.
10Hz
100Hz
1. 0kHz
10kHz
100kHz
1.
0MHz
-100
-50
0
dB
VHR=203mV
VHR=167mV
VHR=134mV
VHR=103mV
VHR=256mV
VHR=300mV
Vout = 3.3V, ILOAD = 10A
Frequency
Vout = 15V, ILOAD = 10A
10Hz
-100
-50
0
dB
1.0kHz
10kHz
100kHz
1. 0MHz
Frequency
100Hz
VHR=203mV
VHR=167mV
VHR=134mV
VHR=103mV
VHR=256mV
VHR=300mV
Figure 5 – Attenuation vs Frequency @ 3.3 volts
Figure 6 – Attenuation vs frequency @ 15 volts
Frequency
10Hz
100Hz
1.0kHz
10kHz
100kHz
1. 0MHz
VHR=203mV
VHR=167mV
VHR=134mV
VHR=103mV
VHR=256mV
VHR=300mV
VOUT = 28V, ILOAD = 10A
-100
-50
0
dB
Figure 7 – Attenuation vs Frequency @ 28 volts
相關PDF資料 |
PDF描述 |
|---|---|
| QPO-2EVAL1 | Evaluation Board for QPO-2 Active Output Filter |
| QPO-2L | QPO-2L Low Voltage Output Ripple Attenuator |
| QS54FCT2240ATZB | FCT SERIES, DUAL 4-BIT DRIVER, INVERTED OUTPUT, PZIP20 |
| QS54FCT2240TZB | FCT SERIES, DUAL 4-BIT DRIVER, INVERTED OUTPUT, PZIP20 |
| QS74FCT2244CTZ | FCT SERIES, DUAL 4-BIT DRIVER, TRUE OUTPUT, PZIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| QPO-2EVAL1 | 制造商:VICOR 制造商全稱:Vicor Corporation 功能描述:Evaluation Board for QPO-2 Active Output Filter |
| QPO-2-EVAL1 | 功能描述:EVALUATION BOARD FOR QPO-2 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:Picor®, QUIETPOWER® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| QPO-2L | 制造商:POWERBOX 制造商全稱:Powerbox 功能描述:OUTPUT RIPPLE ATTENUATOR |
| QPO-2LZ | 功能描述:0.3-5.5V 20A OUT RIP ATTENUATOR RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
| QPO-2LZ-01 | 功能描述:IC INTERFACE FILTER RoHS:是 類別:集成電路 (IC) >> 接口 - 濾波器 - 有源 系列:Picor®, QUIETPOWER® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 濾波器類型:連續時間，帶通低通 頻率 - 截止或中心:150kHz 濾波器數:4 濾波器階數:8th 電源電壓:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。