- 您現在的位置：買賣IC網 > PDF目錄4151 > XC4028XL-1HQ208I (Xilinx Inc)IC FPGA I-TEMP 3.3V 1SPD 208HQFP PDF資料下載
參數資料
| 型號： | XC4028XL-1HQ208I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 14/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA I-TEMP 3.3V 1SPD 208HQFP |
| 產品變化通告： | Product Discontinuation 19/Feb/2007 |
| 標準包裝： | 1 |
| 系列： | XC4000E/X |
| LAB/CLB數： | 1024 |
| 邏輯元件/單元數： | 2432 |
| RAM 位總計： | 32768 |
| 輸入/輸出數： | 160 |
| 門數： | 28000 |
| 電源電壓： | 3 V ~ 3.6 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 208-BFQFP 裸露焊盤 |
| 供應商設備封裝： | 208-PQFP（28x28） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
R
May 14, 1999 (Version 1.6)
6-25
XC4000E and XC4000X Series Field Programmable Gate Arrays
6
Output Multiplexer/2-Input Function Generator
(XC4000X only)
As shown in Figure 16 on page 21, the output path in the
XC4000X IOB contains an additional multiplexer not avail-
able in the XC4000E IOB. The multiplexer can also be con-
gured as a 2-input function generator, implementing a
pass-gate, AND-gate, OR-gate, or XOR-gate, with 0, 1, or 2
inverted inputs. The logic used to implement these func-
tions is shown in the upper gray area of Figure 16.
When congured as a multiplexer, this feature allows two
output signals to time-share the same output pad; effec-
tively doubling the number of device outputs without requir-
ing a larger, more expensive package.
When the MUX is congured as a 2-input function genera-
tor, logic can be implemented within the IOB itself. Com-
bined with a Global Early buffer, this arrangement allows
very high-speed gating of a single signal. For example, a
wide decoder can be implemented in CLBs, and its output
gated with a Read or Write Strobe Driven by a BUFGE
buffer, as shown in Figure 19. The critical-path pin-to-pin
delay of this circuit is less than 6 nanoseconds.
As shown in Figure 16, the IOB input pins Out, Output
Clock, and Clock Enable have different delays and different
exibilities regarding polarity. Additionally, Output Clock
sources are more limited than the other inputs. Therefore,
the Xilinx software does not move logic into the IOB func-
tion generators unless explicitly directed to do so.
The user can specify that the IOB function generator be
used, by placing special library symbols beginning with the
letter “O.” For example, a 2-input AND-gate in the IOB func-
tion generator is called OAND2. Use the symbol input pin
labelled “F” for the signal on the critical path. This signal is
placed on the OK pin — the IOB input with the shortest
delay to the function generator. Two examples are shown in
Other IOB Options
There are a number of other programmable options in the
XC4000 Series IOB.
Pull-up and Pull-down Resistors
Programmable pull-up and pull-down resistors are useful
for tying unused pins to Vcc or Ground to minimize power
consumption and reduce noise sensitivity. The congurable
pull-up resistor is a p-channel transistor that pulls to Vcc.
The congurable pull-down resistor is an n-channel transis-
tor that pulls to Ground.
The value of these resistors is 50 k
100 k. This high
value makes them unsuitable as wired-AND pull-up resis-
tors.
The pull-up resistors for most user-programmable IOBs are
active during the conguration process. See Table 22 on
page 58 for a list of pins with pull-ups active before and dur-
ing conguration.
After conguration, voltage levels of unused pads, bonded
or un-bonded, must be valid logic levels, to reduce noise
sensitivity and avoid excess current. Therefore, by default,
unused pads are congured with the internal pull-up resis-
tor active. Alternatively, they can be individually congured
with the pull-down resistor, or as a driven output, or to be
driven by an external source. To activate the internal
pull-up, attach the PULLUP library component to the net
attached to the pad. To activate the internal pull-down,
attach the PULLDOWN library component to the net
attached to the pad.
Independent Clocks
Separate clock signals are provided for the input and output
ip-ops. The clock can be independently inverted for each
ip-op within the IOB, generating either falling-edge or ris-
ing-edge triggered ip-ops. The clock inputs for each IOB
are independent, except that in the XC4000X, the Fast
Capture latch shares an IOB input with the output clock pin.
Early Clock for IOBs (XC4000X only)
Special early clocks are available for IOBs. These clocks
are sourced by the same sources as the Global Low-Skew
buffers, but are separately buffered. They have fewer loads
and therefore less delay. The early clock can drive either
the IOB output clock or the IOB input clock, or both. The
early clock allows fast capture of input data, and fast
clock-to-output on output data. The Global Early buffers
that drive these clocks are described in “Global Nets and
Global Set/Reset
As with the CLB registers, the Global Set/Reset signal
(GSR) can be used to set or clear the input and output reg-
isters, depending on the value of the INIT attribute or prop-
erty. The two ip-ops can be individually congured to set
IPAD
F
OPAD
FAST
BUFGE
OAND2
from
internal
logic
X9019
Figure 19: Fast Pin-to-Pin Path in XC4000X
OAND2
F
X6598
D0
S0
D1
O
OMUX2
X6599
Figure 20: AND & MUX Symbols in XC4000X IOB
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC4028XL-1HQ208C | IC FPGA C-TEMP 3.3V 1SPD 208HQFP |
| RSC65DRAH-S734 | CONN EDGECARD 130PS .100 R/A PCB |
| RMC65DRAH-S734 | CONN EDGECARD 130PS .100 R/A PCB |
| ACB64DHBS | CONN EDGECARD 128PS R/A .050 DIP |
| ASC49DRAS | CONN EDGECARD 98POS .100 R/A DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC4028XL-1HQ240C | 功能描述:IC FPGA C-TEMP 3.3V 1SPD 240HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4028XL-1HQ240I | 功能描述:IC FPGA I-TEMP 3.3V 1SPD 240HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4028XL-1HQ304C | 功能描述:IC FPGA C-TEMP 3.3V 1SPD 304HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4028XL-1HQ304I | 功能描述:IC FPGA I-TEMP 3.3V 1SPD 304HQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:XC4000E/X 標準包裝:1 系列:Kintex-7 LAB/CLB數:25475 邏輯元件/單元數:326080 RAM 位總計:16404480 輸入/輸出數:350 門數:- 電源電壓:0.97 V ~ 1.03 V 安裝類型:表面貼裝 工作溫度:0°C ~ 85°C 封裝/外殼:900-BBGA，F(xiàn)CBGA 供應商設備封裝:900-FCBGA（31x31） 其它名稱:122-1789 |
| XC4028XL1PG299C | 制造商:XILINX 功能描述:New |
發布緊急采購，3分鐘左右您將得到回復。