- 您現在的位置：買賣IC網 > PDF目錄372199 > SP8527BS Micropower Sampling 10-Bit A/D Converter PDF資料下載
參數資料
| 型號： | SP8527BS |
| 英文描述： | Micropower Sampling 10-Bit A/D Converter |
| 中文描述： | 微采樣10位A / D轉換器 |
| 文件頁數： | 6/12頁 |
| 文件大小： | 180K |
| 代理商： | SP8527BS |
SP8527DS/01
SP8527 Micropower Sampling 10-Bit A/D Converter
6
Copyright 2000 Sipex Corporation
Single Ended or Full
Differential Operation
The
SP8527
has a balanced full differential front
end. The
SP8527
can be used in this manner, or
it can be used in single-ended circuits as well.
For single-ended systems, simply tie the -IN to
the Reference Low of the input signal, which is
allowed to range from 0V to V
. For a full
differential sampling configuration, both inputs
are sampled and held simultaneously. Because
of the balanced differential sampling, dynamic
common mode noise riding along the input
signal is cancelled above and beyond DC noise.
This is a significant improvement over psuedo-
differential sampling schemes, where the low
side of the input must remain constant during
the conversion, and therefore only DC noise (i.e.
signal offset) is cancelled. If AC common mode
noise is left to be converted along with the
differental component, the output signal will be
degraded.
Full differential sampling allows flexibility in
converting the input signal. If the signal low- side
is already tied to a ground elsewhere in the
system, it can be hardwired to the low side
input (i.e., -IN) which acts as a signal ground
sense, breaking a potential ground loop. It is also
possible to drive the inputs balanced differential,
as long as both inputs are within the power rails.
In this configuration, both the high and low
signals have the same impedance looking back
to ground, and therefore pick up the same noise
along the physical path from signal source (i.e.,
sensor, transducer, battery) to the converter. This
noise becomes common mode, and is cancelled
out by the differential sampling of the
SP8527
.
Layout Considerations
To preserve the high resolution and linearity of
the
SP8527
attention must be given to circuit
board layout, ground impedance and bypassing.
A circuit board layout which includes separate
analog and digital ground planes will prevent
the coupling of noise into sensitive converter
circuits and will help to preserve the dynamic
performance of the device. In single ended
mode, the analog input signal should be
referenced to the ground pin of the converter.
This prevents any voltage drops
that occur in
the power supply's common return from appearing
in series with the input signal.
In full differential mode, the high and low side
board traces should run close to each other, with
the same layout. This will insure that any noise
coupling will be common mode, and cancelled
by the converters (patent pending) full differential
architecture.
If separate analog and digital ground planes are
not possible, care should be used to prevent
coupling between analog and digital signals. If
analog and digital lines must cross, they should
do so at right angles. Parallel analog and digital
lines should be separated by a circuit board trace
which is connected to common.
The reference pin on the
SP8527
should be kept
as clean as possible. A noise signal of 4.88mV
(for VREF = 5.0V) will produce 1 lsb of error
in the output code. For convenience, the VREF
pin can be tied to the VCC pin, but now the same
care should be taken with the VCC pin as with
the VREF pin. Whether or not VCC is tied to
VREF, the VCC pin should always be bypassed
to the GROUND pin with a parallel combination
of a 6.8
μ
F tantalum and a 0.1
μ
F ceramic
capacitor. To maintain maximum system
accuracy, the supply connected to the VCC pin
should be well isolated from digital supplies and
wide load variations. A separate conductor from
the supply regulator to the A/D converter will
limit the effects of digital switching elsewhere
in the system. Power supply noise can degrade
the converters performance. Especially corrupting
are noise and spikes from a switching
power supply.
To avoid introducing distortion when driving the
A/D converter input, the input signal source
should be able to charge the
SP8527's
equivalent
20 pF of input capacitance from zero volts to
the signal level in 1.5 clock periods.
相關PDF資料 |
PDF描述 |
|---|---|
| SP8527KN | Micropower Sampling 10-Bit A/D Converter |
| SP8527KS | Micropower Sampling 10-Bit A/D Converter |
| SP8528 | Micropower Sampling 12-Bit A/D Converter |
| SP8530 | S2ADC - Simultaneous Sampling Analog to Digital Converter |
| SP8530AN | S2ADC - Simultaneous Sampling Analog to Digital Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP8527KN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Micropower Sampling 10-Bit A/D Converter |
| SP8527KS | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Micropower Sampling 10-Bit A/D Converter |
| SP8528 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Micropower Sampling 12-Bit A/D Converter |
| SP8530 | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:S2ADC - Simultaneous Sampling Analog to Digital Converter |
| SP8530AN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:S2ADC - Simultaneous Sampling Analog to Digital Converter |
發布緊急采購，3分鐘左右您將得到回復。