參數資料
型號： VT900
廠商： PerkinElmer Inc.
英文描述： Photoconductive Cells and Analog Optoisolators (Vactrols)
中文描述： 光導細胞和模擬光隔離器（Vactrols）
文件頁數： 33/76頁
文件大?。?/td> 1240K
代理商： VT900
28
What Are Analog Optical Isolators
PerkinElmer Optoelectronics has been a leading manufacturer of
analog optical isolators for over twenty years and makes a broad range
of standard parts under its trademark VACTROL
There are many kinds of optical isolators, but the most common is the
LED/phototransistor type. Other famliar types use output elements
such as light sensitive SCRs, Triacs, FETs, and ICs. The major
application for these silicon based devices is to provide electrical
isolation of digital lines connected between different pieces of
equipment. The principle of operation is very simple. When an input
current is applied to the LED, the output phototransistor turns on. The
only connection between the LED and phototransistor is through
light—not electricity, thus the termoptical isolator. These optical
isolators are primarily digital in nature with fast response times suitable
for interfacing with logic gates. Rise and fall times of a few
mcroseconds, faster for some isolators, are typical.
The analog optical isolator (AOI) also uses an optical link between
input and output. The input element is an LED and the output element
is always photoconductive cell or simply photocell. Together, the
coupled pair act as an electrically variable potentiometer. since the
output element of the AOI is a resistor, the voltage applied to this
output resistor may be DC and/or AC and the magnitude may be as
low as zero or as high as the maximumvoltage rating. Because the
input will control the magnitude of a complex waveformin a
proportional manner this type of isolator is an analog control element.
AOIs may be used in the ON-OFF mode but the fastest response time
is only in the mllisecond range. A level sensitive Schmtt trigger is
required between the AOI and logic gates when used in digital circuits.
The figure below shows the circuit diagramof a standard AOI.
AOI Circuit Diagram
Input Element
Light emtting diodes used in AOIs are usually visible LEDs best
matching the sensitivity spectrumof the photocell output element.
LEDs are the ideal input element in most applications. They require
low drive current and voltage, respond very fast and have virtually
unlimted life. They are very rugged and are unaffected by shock and
vibration. Since the LED is a diode, it conducts in one direction only.
They must be protected fromexcessive forward current due to the low
dynamc resistance in the forward direction. The forward characteristic
of an LED typically used in VACTROLs is shown below.
LED Forward Characteristics
Output Element
The output element in all PerkinElmers AOIs is a light dependent
resistor (LDR), also called a photoconductor or photocell. Photocells
are true resistors.
These passive resistors are made froma light sensitive polycrystalline
semconductor thin filmwhich has a very high electron/photon gain.
There are no P/N junctions in a photocell, making it a bilateral device.
The resistance of the photocell depends on the amount of light falling
on the cell. For a given illumnation, the amount of electrical current
through the cell depends on the voltage applied. This voltage may be
either AC or DC. Thus, the photocell is the ideal low distortion output
element for an analog optoisolator.
A complete discussion of photoconductive cells can be found in the
first section of this book.
相關PDF資料
PDF描述
VT905GA
VT905GC
VT90N1
VT90N2
VT90N3
相關代理商/技術參數
參數描述
VT905GA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
VT905GB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
VT905GC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
VT90A114 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
VT90A432 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*