- 您現在的位置：買賣IC網 > PDF目錄372950 > XRT73L00 (Exar Corporation) E3/DS3/STS-1 LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT73L00 |
| 廠商： | Exar Corporation |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT |
| 中文描述： | E3/DS3/STS-1線路接口單元 |
| 文件頁數： | 6/53頁 |
| 文件大小： | 604K |
| 代理商： | XRT73L00 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
XRT73L00
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.2.0
á
3
PIN DESCRIPTION
PIN DESCRIPTION
P
IN
#
S
YMBOL
T
YPE
D
ESCRIPTION
1
TXLEV
I
Transmit Line Build-Out Enable/Disable Select:
This input pin is used to enable or disable the Transmit Line Build-Out circuit in
the XRT73L00.
Setting this pin to “High” disables the Line Build-Out circuit. In this mode, the
XRT73L00 outputs partially shaped pulses onto the line via the TTIP and TRING
output pins.
Setting this pin to “Low” enables the Line Build-Out circuit. In this mode, the
XRT73L00 outputs partially-shaped pulses onto the line via the TTIP and TRING
output pins.
To comply with the isolated DSX-3/STSX-1 Pulse Template Requirements per
Bellcore GR-499-Core or Bellcore GR-253-Core:
1. Set this input pin to a "1" if the cable length between the Cross-Connect and
the transmit output of the XRT73L00 is greater than 225 feet.
2. Set this input pin to a "0" if the cable length between the Cross-Connect and
the transmit output of the XRT73L00 is less than 225 feet.
This pin is active only if both of the following are true:
(a) The XRT73L00 is configured to operate in either the DS3 or SONET STS-1
modes and
(b) The XRT73L00 is configured to operate in the Hardware Mode.
N
OTE
:
This pin should be tied to GND if the XRT73L00 is to be operated in the
HOST mode.
2
TAOS
I
Transmit All Ones Select:
A “High” on this pin causes a continuous AMI all “1’s” pattern to be transmitted
onto the line. The frequency of this “1’s” pattern is determined by TCLK.
N
OTES
:
1. This input pin is ignored if the XRT73L00 is operating in the HOST
Mode.
2. Tie this pin to GND if the XRT73L00 is going to be operating in the
HOST Mode.
3
TxAVDD
****
Transmit Analog Power Supply
4
DMO
O
Drive Monitor Output:
If no bipolar line signal is detected on the TTIP/TRING output pins via the MTIP
and MRING input pins for 128±32 TCLK periods, then the DMO output pin tog-
gles and remains “High” until the next bipolar pulse is detected.
5
TxAGND
****
Transmit Analog Ground
6
AGND
****
Analog Ground (Substrate)
7
RxAGND
****
Receive Analog Ground
8
RTIP
I
Receive TIP Input:
This input pin along with RRING is used to receive the line signal from the
Remote DS3/E3/STS-1 Terminal.
9
RRING
I
Receive RING Input:
This input pin along with RTIP is used to receive the line signal from the Remote
DS3/E3/STS-1 Terminal.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L00A | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AIV | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT75L03DIV | Telecomm/Datacomm |
| XRT75L00 | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
| XRT75L00IV | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73L00A | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面開發工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XRT73L00AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LINE INTERFACE|QFP|44PIN|PLASTIC |
| XRT73L02M | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。