參數資料
型號： μPD75F4246(A)
廠商： NEC Corp.
元件分類： 8位微控制器
英文描述： 8 Bit Single Chip Microcontrollers
中文描述： 8位單片機微控制器
文件頁數： 27/143頁
文件大?。?/td> 549K
代理商： ΜPD75F4246(A)
15
CHAPTER 3 WRITE SEQUENCE
CHAPTER 3 WRITE SEQUENCE
3.1 Write Sequence
This command indicates the timing and processing time related to the transmission of commands. Here, the
processing time refers to the
μ
PD75F4264’s processing time. The commands and data described below cannot be
sent normally until a wait time consisting of the following number of clocks has elapsed. The clock referred to below
is the
μ
PD75F4264’s operating clock.
The following commands are issued after the steps described above in “switching to power on/write mode” and
“synchronization detection processing” (which uses the reset command) have been completed. The communication
format is LSB first, with no start/stop bits.
3.1.1 Reset command
This command initializes the
μ
PD75F4264’s mode and is also used to confirm synchronization detection as part
of synchronization detection processing.
Figure 3-1. Timing of Reset Command
Note
Once a NACK signal is returned, retries are performed until an ACK signal is returned. The maximum
number of retries is 16. A communication error occurs if 17 or more retries are attempted.
For details, see
CHAPTER 4 SAMPLE PROGRAMS
.
Remarks 1.
Wait1: This wait time is at least 800 pulses of the CPU clock. It is the wait time between issuing
a command and receiving an ACK signal.
2.
Wait2: This wait time is at least 700 pulses of the CPU clock. It is the wait time that occurs
between receiving an ACK signal and sending or receiving data, between data
transmissions, between sending or receiving data and receiving an ACK signal, and
between issuing commands.
SCK
SI
SO
COMMAND
“00”
Wait1
NACK = “00”
Note
“00”
Wait2
COMMAND
“00”
Wait1
ACK = “3C”
“3C”
(Retries: 16 maximum)
相關PDF資料
PDF描述
μPD75F4246 8 Bit Single Chip Microcontrollers
μPD75F4246A 8 Bit Single Chip Microcontrollers
μPD75P0116 4 Bit RISC Microcontrollers(4 位單片微控制器)
μPD75P3116 4 Bit Single Chip Microcontrollers(4位單片微控制器)
μPD75P3216 4 Bit Single Chip Microcontrollers(4位單片微控制器)
相關代理商/技術參數
參數描述
PD75G6FK13 制造商:American Power Conversion Corp (APC by Schneider Electric) 功能描述:75KVA PDU W/ 480 PRI 208/120 SEC K13 RATED XMER 制造商:Schneider Electric 功能描述:APC 75KVA PDU W/ 480 PRI 20 - Bulk
PD75R-103K 功能描述:固定電感器 10uH 10% .08ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75R-104K 功能描述:固定電感器 100uH 10% .5ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
PD75R-104K/R500 制造商:API Delevan 功能描述:PD75R series 100 uH 10 % 740 mA SMT Power Choke
PD75R-123K 功能描述:固定電感器 12uH 10% .085ohm Choke SMT Power Ind RoHS:否 制造商:AVX 電感:10 uH 容差:20 % 最大直流電流:1 A 最大直流電阻:0.075 Ohms 工作溫度范圍:- 40 C to + 85 C 自諧振頻率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接類型:SMD/SMT 封裝 / 箱體:6.6 mm x 4.45 mm
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*