參數資料
型號: μPD78F9831
廠商: NEC Corp.
英文描述: 8 Bit Single Chip Microcontrollers(8 位微控制器)
中文描述: 8位單片機微控制器(8位微控制器)
文件頁數: 96/211頁
文件大?。?/td> 1262K
代理商: ΜPD78F9831
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁當前第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁
CHAPTER 5 CLOCK GENERATION CIRCUIT
96
5.5 Clock Generation Circuit Operation
The clock generation circuit generates the following clocks and controls operation modes of the CPU, such as
standby mode:
Main system clock f
X
Subsystem clock f
XT
CPU clock f
CPU
Clock to peripheral hardware
The operation of the clock generation circuit is determined by the processor clock control register (PCC),
suboscillation mode register (SCKM), and subclock control register (CSS), as follows:
(a)
The slow mode 2f
CPU
(2.23
μ
s: at 3.58-MHz operation) of the main system clock is selected when the
RESET signal is generated (PCC = 02H). While a low level is input to the RESET pin, oscillation of
the main system clock is stopped.
(b)
Three types of CPU clocks f
CPU
(0.28
μ
s and 1.12
μ
s: main system clock (at 3.58-MHz operation), 61
μ
s: subsystem clock (at 32.768 kHz operation)) can be selected by the PCC, SCKM, and CSS
settings.
(c)
Two standby modes, STOP and HALT, can be used with the main system clock selected. In a system
where no subsystem clock is used, setting bit 1 (FRC) of SCKM so that the on-chip feedback resistor
cannot be used reduces current drain during STOP mode. In a system where a subsystem clock is
used, setting SCKM bit 0 to 1 can cause the subsystem clock to stop oscillation.
(d)
CSS bit 4 (CSS0) can be used to select the subsystem clock so that low power dissipation operation is
used (at 122
μ
s, 32.768 kHz operation).
(e)
With the subsystem clock selected, it is possible to cause the main system clock to stop oscillating
according to bit 7 (MCC) of PCC. HALT mode can be used, but STOP mode cannot.
(f)
The clock pulse for the peripheral hardware is generated by dividing the frequency of the main system
clock. The subsystem clock pulse is supplied to the clock output circuit, LCD controller/driver, and
watch timer only. So, also at standby, the clock output circuit, LCD controller/driver, and clock function
can keep running. The other hardware stops when the main system clock stops, because it runs
based on the main system clock (except for external clock pulses).
相關PDF資料
PDF描述
μPD78F0974 8 Bit Single Chip Microcontrollers
μPD78F0988 8 Bit Single Chip Microcontrollers
μPD78F225GC 16 Bit General-Purpose Microcontrollers(16位通用微控制器)
μPD78215GC 16 Bit General-Purpose Microcontrollers(16位通用微控制器)
μPD78215GF 16 Bit General-Purpose Microcontrollers(16位通用微控制器)
相關代理商/技術參數
參數描述
PD7935 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:FOR OPTICAL COMMUNICATION
PD7937 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES
PD793D26 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES
PD793D7 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:InGaAs PIN PHOTO DIODES
PD79920-0M 制造商:Citizen Systems America Corporation 功能描述:Mobile Printer - PD24 USB Cable