- 您現在的位置：買賣IC網 > PDF目錄24626 > 051-C51-9039 (ITT Corporation) RF Coaxial Connectors PDF資料下載
參數資料
| 型號： | 051-C51-9039 |
| 廠商： | ITT Corporation |
| 英文描述： | RF Coaxial Connectors |
| 中文描述： | 射頻同軸連接器 |
| 文件頁數： | 31/42頁 |
| 文件大?。?/td> | 489K |
| 代理商： | 051-C51-9039 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
Dimensions are shown in mm (inch)
Dimensions subject to change
138
RF Coaxial Connectors
Assembly Instructions
BBAI-1238
SMZ QTTM Connectors for Braided Cable
1. Prepare cable, using a suitable stripping, tool to the dimensions shown being careful not to damage the
braid, dielectric or inner conductor.
NOTE: Do not attempt to mate unterminated connectors.
2. Trim center conductor to dimensions shown by inserting conductor through the hole in the center of
the assembly tool and trimming, with sharp side cutters, flush with the face of the tool. DIMENSIONS
CAN BE CHECKED USING THE TEMPLATE ON THE REAR FACE OF THE ASSEMBLY TOOL.
3. ENSURE THAT THE INNER CONDUCTOR IS STRAIGHT. Slide the crimp ferrule over the cable sheath.
Fit the connector body onto the cable so that the rear body slides between the dielectric and the braid
(gently twisting and rocking the connector body to spread the braid will help). Care must be taken to
ensure that no strands of braid are trapped under the body. A small gap [2,00 (.079) maximum] should
be evident between braid and face of body.
4. Support cable/connector in one hand. Press home insulator using assembly tool provided, using the
larger for the DDF jack and the smaller for the Posilock plug.
5. Slide the crimp ferrule forward, over the braid, until it butts up against the rear of the connector. Crimp
using ITT Cannon crimp tool fitted with a suitable die set (see table).
Cable
Die Size
BT2003
6,81 (.268)
BT3002
4,52 (.178)
TZC75024
4,52 (.178)
ASSEMBLY TOOL
CONNECTOR
FERRULE
相關PDF資料 |
PDF描述 |
|---|---|
| 92HD202DX5PRGXYYX8 | PCM CODEC, PQFP48 |
| 92HD202XX5PRGXYYX8 | PCM CODEC, PQFP48 |
| 051-F53-9019A9H | 1.0/2.3 RF Connector Series |
| 92HD206XX5PRGXYYX8 | PCM CODEC, PQFP48 |
| 92HD206DX5PRGXYYX8 | PCM CODEC, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 051F0049 REV D | 制造商:MISCELLANEOUS 功能描述: |
| 051-F53-9019A9H | 制造商:ITT 制造商全稱:ITT Industries 功能描述:1.0/2.3 RF Connector Series |
| 051-F53-9019A9H0 | 制造商:ITT Interconnect Solutions 功能描述:SMB 50OHM PCB MOUNT JACK - Bulk |
| 051-F53-9029A9H | 制造商:ITT 制造商全稱:ITT Industries 功能描述:1.0/2.3 RF Connector Series |
| 051-F53-9059EAA | 制造商:ITT Interconnect Solutions 功能描述:Conn 1.0/2.3 F 0Hz to 2GHz 75Ohm Solder RA Thru-Hole Gold Over Nickel Tray |
發布緊急采購，3分鐘左右您將得到回復。