- 您現在的位置：買賣IC網 > PDF目錄368694 > 100390 (Fairchild Semiconductor Corporation) Low Power Single Supply Hex PECL-to-TTL Translator(低功耗、單電源、六PECL電平到TTL電平轉換器) PDF資料下載
參數資料
| 型號： | 100390 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Low Power Single Supply Hex PECL-to-TTL Translator(低功耗、單電源、六PECL電平到TTL電平轉換器) |
| 中文描述： | 低功耗單電源六角PECL的到的TTL翻譯（低功耗，單電源，六PECL的電平到的TTL電平轉換器） |
| 文件頁數： | 6/8頁 |
| 文件大小： | 96K |
| 代理商： | 100390 |
www.fairchildsemi.com
6
1
Application Notes
1. Device performance will be enhanced by the use of
dual V
CC
power planes as illustrated in the Application
Figures 4, 5. This will minimize the coupling of TTL
switching noise into the primary reference to the ECL
circuitry and take full advantage of the 100390
’
s on
chip V
CC
partitioning.
2. The device
’
s partitioned V
CC
may be operated from two
5V, 5% tolerance, supplies provided that they are
ramped up/down together so that the max differential is
1V. This is to prevent overstress to internal ESD
diodes. If the ECL driver to the F390 is powered from a
separate supply, it must obey this sequence rule also.
3. Glitch-free power up, independent of Data input levels,
is achieved if TTL logic HIGH is held on the Output
Enable pin during ramping up/down of the V
CC
supply.
4. Undefined output states can occur for some invalid
combinations. See Truth Table. This should be avoided
to prevent possible oscillation or increased power con-
sumption due to TTL outputs biased into a quasi state
with both pullup and pulldown stages partially on.
3-STATEing the outputs will counteract the effects of
invalid input states.
5. Pins 8, 15, and 22 on the 28-pin PLCC package are
tied to the chip
’
s substrate and are named GNDs.
These pins are electrically common to the ground pins
1, 2, and 28. For best thermal performance, tie the
GND pins to the circuit ground plane. They may be tied
to an electrically isolated thermal dissipation plane or
may float.
6. Figure 4 illustrates typical differential input operation.
7. Figure 5 illustrates typical single-ended input operation.
FIGURE 4.
FIGURE 5.
相關PDF資料 |
PDF描述 |
|---|---|
| 100390SC | Low Power Single Supply Hex PECL-to-TTL Translator |
| 100390QCX | ECL-to-TTL Translator |
| 100390QIX | ECL-to-TTL Translator |
| 100390SCX | ECL-to-TTL Translator |
| 100390QC | Low Power Single Supply Hex PECL-to-TTL Translator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 100390PC | 功能描述:轉換 - 電壓電平 Hex PECL-to-TTL Tran RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| 100390QC | 功能描述:轉換 - 電壓電平 Hex PECL-to-TTL Tran RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| 100390QCX | 功能描述:轉換 - 電壓電平 Hex PECL-to-TTL Tran RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| 100390QI | 功能描述:轉換 - 電壓電平 Hex PECL-to-TTL Tran RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| 100390QIX | 功能描述:轉換 - 電壓電平 Hex PECL-to-TTL Tran RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。