- 您現在的位置：買賣IC網 > PDF目錄351527 > 100511038 WINKELVERSCHRAUB SCHWENK 10MM 0.375 PDF資料下載
參數資料
| 型號： | 100511038 |
| 英文描述： | WINKELVERSCHRAUB SCHWENK 10MM 0.375 |
| 中文描述： | WINKELVERSCHRAUB施文克10毫米0.375 |
| 文件頁數： | 17/17頁 |
| 文件大?。?/td> | 269K |
| 代理商： | 100511038 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相關PDF資料 |
PDF描述 |
|---|---|
| 1005-112 | Analog IC |
| 100511248 | WINKELVERSCHRAUB SCHWENK 12MM 0.5 |
| 100CJB | Fuse |
| 100D125 | Fuse |
| 100FE | Fuse |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10051110 | 制造商:Fluke Networks 功能描述:D914 Impact Tool with EverSharp 110 Blade |
| 10-0511-10 | 功能描述:IC 與器件插座 STRIP LINE SOCKETS 10 PINS TIN RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 10-0511-11 | 功能描述:IC 與器件插座 STRIP LINE SOCKETS 10 PINS GOLD RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 1005111-1 | 制造商:OMNIMOUNT 功能描述:FIXED MOUNT FOR 13 - 32 INCH FLAT PANELS |
| 1005-112 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。