參數資料
型號: 101-0488
廠商: Rabbit Semiconductor
文件頁數: 7/90頁
文件大?。?/td> 0K
描述: MODULE RABBITCORE RCM2210
標準包裝: 1
系列: RabbitCore®
模塊/板類型: 單板計算機模塊
適用于相關產品: RCM2210
User’s Manual
9
To power down the Prototyping Board, unplug the power connector from J5. You should
disconnect power before making any circuit adjustments in the prototyping area, changing
any connections to the board, or removing the RabbitCore module from the board.
2.1.4 Alternate Power Supply Connections
Development kits sold outside North America before 2009 included a header connector
that could be connected to 3-pin header J5 on the Prototyping Board. The red and black
wires from the connector could then be connected to the positive and negative connections
on your power supply. The power supply should deliver 8 V–24 V DC at 8 W.
2.2 Run a Sample Program
Once the RCM2200 is connected as described in the preceding pages, start Dynamic C by
double-clicking on the Dynamic C icon on your desktop or in your Start menu. Dynamic C
uses the serial port specified during installation.
If you are using a USB port to connect your computer to the RCM2200 module, choose
Options > Project Options
and select “Use USB to Serial Converter” under the
Communications
tab, then click OK.
Find the file PONG.C, which is in the Dynamic C SAMPLES folder. To run the program,
open it with the File menu (if it is not still open), then compile and run it by pressing F9 or
by selecting Run in the Run menu. The STDIO window will open and will display a small
square bouncing around in a box.
2.2.1 Troubleshooting
If Dynamic C cannot find the target system (error message "No Rabbit Processor
Detected."
):
Check that the RCM2200 is powered correctly — the red power LED on the Prototyping
Board should be lit when the RCM2200 is mounted on the Prototyping Board and the AC
adapter is plugged in
.
Check both ends of the programming cable to ensure that they are firmly plugged into
the PC and the PROG connector, not the DIAG connector, is plugged in to the program-
ming port on the RCM2200 with the marked (colored) edge of the programming cable
towards pin 1 of the programming header.
Ensure that the RCM2200 module is firmly and correctly installed in its connectors on
the Prototyping Board.
Dynamic C uses the COM port specified during installation. Select a different COM
port within Dynamic C. From the Options menu, select Project Options, then select
Communications
. Select another COM port from the list, then click OK. Press
<Ctrl-Y>
to force Dynamic C to recompile the BIOS. If Dynamic C still reports it is
unable to locate the target system, repeat the above steps until you locate the COM port
used by the programming cable.
相關PDF資料
PDF描述
AT45DB321B-TC IC FLASH 32MBIT 20MHZ 32TSOP
AT45DB011B-SC IC FLASH 1MBIT 20MHZ 8SOIC
SOMOMAP3530-11-1670EFCR SYSTEM ON MODULE LV OMAP3530
395-030-523-202 CARD EDGE 30POS DL .100X.200 BLK
395-030-523-201 CARD EDGE 30POS DL .100X.200 BLK
相關代理商/技術參數
參數描述
101-0492 功能描述:單板計算機 OP6800 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
101-0494 功能描述:模塊化系統 - SOM RCM2250 RABBITCORE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
101-0495 功能描述:處理器配件 Baseplate RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
101-0497 功能描述:單板計算機 OP6810 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
10104997-00C-10B 功能描述:高速/模塊連接器 XCEDE 2W 6PVH 6COL RoHS:否 制造商:Molex 系列:iPass 產品類型: 排數: 列數: 位置/觸點數量:38 安裝角:Right 節距:0.8 mm 安裝風格:Plug 端接類型:SMD/SMT 外殼材料:Thermoplastic 觸點材料:High Performance Alloy (HPA) 觸點電鍍:Gold