- 您現在的位置：買賣IC網 > PDF目錄351527 > 101151248 STECKSTUTZEN EINSCHRAUB 12MM BSP 0.5 PDF資料下載
參數資料
| 型號： | 101151248 |
| 英文描述： | STECKSTUTZEN EINSCHRAUB 12MM BSP 0.5 |
| 中文描述： | STECKSTUTZEN EINSCHRAUB 12毫米BSP的0.5 |
| 文件頁數： | 17/17頁 |
| 文件大?。?/td> | 269K |
| 代理商： | 101151248 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相關PDF資料 |
PDF描述 |
|---|---|
| 1012-0100 | MATRIX DRUCKER TRAGBAR SERIELL 24SPALTEN |
| 101-205-02 | LED SUBMIN PCB MNT RED |
| 101-205-20 | LED PCB MOUNT RED |
| 1012-105 | Analog IC |
| 1012-106 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10115130-001LF | 功能描述:板對板與夾層連接器 535-57BF-MEZZO STACK .5MM RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
| 10115130-004LF | 制造商:FCI 功能描述:OEM ITEM 521-57BF-MEZZO STACK .5MM |
| 10115130-005LF | 功能描述:24 Position Connector Self Mating, Non-Gendered Surface Mount Gold or Gold, GXT? 制造商:amphenol fci 系列:- 包裝:帶卷（TR） 零件狀態:有效 連接器類型:無公形或母形之分，自配接 針腳數:24 間距:0.020"（0.50mm） 排數:2 安裝類型:表面貼裝 特性:板導軌 觸頭鍍層:金或金，GXT? 觸頭鍍層厚度:- 接合堆疊高度:- 板上高度:- 標準包裝:1,000 |
| 10115130-006LF | 功能描述:24 Position Connector Self Mating, Non-Gendered Surface Mount Gold or Gold, GXT? 制造商:amphenol fci 系列:- 包裝:帶卷（TR） 零件狀態:有效 連接器類型:無公形或母形之分，自配接 針腳數:24 間距:0.020"（0.50mm） 排數:2 安裝類型:表面貼裝 特性:- 觸頭鍍層:金或金，GXT? 觸頭鍍層厚度:- 接合堆疊高度:- 板上高度:- 標準包裝:1,000 |
| 10115130-037LF | 功能描述:MEZZOSTAK 30P WITH PEG B 制造商:amphenol fci 系列:* 零件狀態:在售 標準包裝:1,000 |
發布緊急采購，3分鐘左右您將得到回復。