- 您現在的位置：買賣IC網 > PDF目錄351528 > 101471248 EINSCHRAUBVERB WINKEL DREHBAR 12MM 0.5 PDF資料下載
參數資料
| 型號： | 101471248 |
| 英文描述： | EINSCHRAUBVERB WINKEL DREHBAR 12MM 0.5 |
| 中文描述： | EINSCHRAUBVERB克爾DREHBAR 12毫米0.5 |
| 文件頁數： | 17/17頁 |
| 文件大小： | 269K |
| 代理商： | 101471248 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相關PDF資料 |
PDF描述 |
|---|---|
| 10150 | PHOSPHORBRONZE TUBE 2X1ZOLL |
| 1015-105 | Analog IC |
| 1015-106 | Analog IC |
| 1015-112 | Analog IC |
| 1015-124 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 101472T063BA2A | 功能描述:ALUM-SCREW TERMINAL 制造商:cornell dubilier electronics (cde) 系列:* 零件狀態:新產品 標準包裝:5 |
| 101472U025AA2B | 功能描述:ALUM-SCREW TERMINAL 制造商:cornell dubilier electronics (cde) 系列:* 零件狀態:新產品 標準包裝:5 |
| 101472U050AC1A | 功能描述:ALUM-SCREW TERMINAL 制造商:cornell dubilier electronics (cde) 系列:* 零件狀態:新產品 標準包裝:5 |
| 1014730000 | 功能描述:CONN TERM BLOCK 5.08MM 2POS BLK RoHS:是 類別:連接器，互連式 >> 接線座 - 接頭，插頭和插口 系列:Omnimate BLF 標準包裝:1 系列:OSTVK 端接塊類型:接頭，公引腳，帶罩（4 面） 每電平位置:18 間距:0.138"（3.50mm） 級別數目:1 接頭定向:45° 插頭導線入口:- 端子:焊接 線規:- 電流:8A 電壓:300V 安裝類型:通孔 特點:- 顏色:綠 包裝:散裝 配套產品:OSTVM181550-ND - TERM BLOCK PLUG 3.50MM 18POSOSTV7181151-ND - TERM BLOCK PLUG 3.50MM 18POSOSTV7181150-ND - TERM BLOCK PLUG 3.50MM 18POSOSTTS18115B-ND - TERM BLOCK PLUG 3.50MM 18POSOSTTS18115A-ND - TERM BLOCK PLUG 3.50MM 18POS |
| 1014740000 | 功能描述:CONN TERM BLOCK 5.08MM 3POS BLK RoHS:是 類別:連接器，互連式 >> 接線座 - 接頭，插頭和插口 系列:Omnimate BLF 標準包裝:1 系列:OSTEZ 端接塊類型:插頭，母插口 每電平位置:11 間距:0.197"（5.00mm） 級別數目:1 接頭定向:- 插頭導線入口:180° 端子:螺釘 線規:12-22 AWG 電流:15A 電壓:300V 安裝類型:自由懸掛 特點:法蘭，固定鎖（非導線側） 顏色:綠 包裝:散裝 配套產品:OSTVL227251-ND - CONN TERM BLK HEADER 22POS 5MMOSTVL227250-ND - CONN TERM BLK HEADER 22POS 5MMOSTVF227251-ND - CONN TERM BLK HEADER 22POS 5MMOSTVF227250-ND - CONN TERM BLK HEADER 22POS 5MMOSTOQ117551-ND - CONN HEADER 11POS 5.0MM R/A PCBOSTOQ117550-ND - CONN HEADER 11POS 5.0MM VERT PCB |
發布緊急采購，3分鐘左右您將得到回復。