- 您現在的位置：買賣IC網 > PDF目錄106304 > 1026SE-42TE13 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 PDF資料下載
參數資料
| 型號： | 1026SE-42TE13 |
| 元件分類： | 電源管理 |
| 英文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 17/17頁 |
| 文件大?。?/td> | 108K |
| 代理商： | 1026SE-42TE13 |
9
Preliminary Information
CAT1026, CAT1027
Doc No. 3010, Rev. E
EMBEDDED EEPROM OPERATION
The CAT1026 and CAT1027 feature a 2kbit embedded
serial EEPROM that supports the I2C Bus data
transmission protocol. This Inter-Integrated Circuit Bus
protocol defines any device that sends data to the bus to
be a transmitter and any device receiving data to be a
receiver. The transfer is controlled by the Master device
which generates the serial clock and all START and
STOP conditions for bus access. Both the Master device
and Slave device can operate as either transmitter or
receiver, but the Master device controls which mode is
activated.
I2C Bus Protocol
The features of the I2C bus protocol are defined as
follows:
(1) Data transfer may be initiated only when the bus is
not busy.
(2) During a data transfer, the data line must remain
stable whenever the clock line is high. Any changes in
the data line while the clock line is high will be interpreted
as a START or STOP condition.
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of
SDA when SCL is HIGH. The CAT1026 and CAT1027
monitor the SDA and SCL lines and will not respond until
this condition is met.
STOP Condition
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
The Master begins a transmission by sending a START
condition. The Master sends the address of the particular
slave device it is requesting. The four most significant
bits of the 8-bit slave address are programmable in metal
and the default is 1010.
The last bit of the slave address specifies whether a
Read or Write operation is to be performed. When this bit
is set to 1, a Read operation is selected, and when set
to 0, a Write operation is selected.
After the Master sends a START condition and the slave
address byte, the CAT1026 and CAT1027 monitor the
bus and responds with an acknowledge (on the SDA
line) when its address matches the transmitted slave
address. The CAT1026 and CAT1027 then perform a
Read or Write operation depending on the R/
W bit.
tHIGH
SCL
SDA IN
SDA OUT
tLOW
tF
tLOW
tR
tBUF
tSU:STO
tSU:DAT
tHD:DAT
tHD:STA
tSU:STA
tAA
tDH
Figure 4. Bus Timing
Figure 5. Write Cycle Timing
tWR
STOP
CONDITION
START
CONDITION
ADDRESS
ACK
8TH BIT
BYTE n
SCL
SDA
相關PDF資料 |
PDF描述 |
|---|---|
| 12IMR6-0505-7 | 2-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| 15IZR1-15-15-T | 2-OUTPUT 1 W DC-DC REG PWR SUPPLY MODULE |
| 12IML10-12-12-0 | 2-OUTPUT 8.4 W DC-DC REG PWR SUPPLY MODULE |
| 12IMR15-05-2 | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| 11274-502-XTD | PLL FREQUENCY SYNTHESIZER, 28 MHz, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10-26UD-AU-16 | 功能描述:0.11 X 0.26 AU 16--10-26UD-AU-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:金 鍍層 - 厚度:閃存 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 10-26UD-BD-16 | 功能描述:0.10 X 0.26 BD 16--10-26UD-BD-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:沒有鍍層 鍍層 - 厚度:- 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 10-26UD-NI-16 | 功能描述:0.10 X 0.26 NI 16--10-26UD-NI-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:鎳 鍍層 - 厚度:閃存 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 10-26UD-SN-16 | 功能描述:0.10 X 0.26 SN 16--10-26UD-SN-16 制造商:leader tech inc. 系列:TechMESH 零件狀態:在售 類型:簧片 形狀:- 寬度:0.260"（6.60mm） 長度:16.000"（406.40mm） 高度:0.110"（2.79mm） 材料:銅鈹 鍍層:錫 鍍層 - 厚度:閃存 接合方法:膠合劑 工作溫度:-55°C ~ 121°C 標準包裝:20 |
| 1026V3-19A | 制造商:undefined 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。