- 您現在的位置：買賣IC網 > PDF目錄62888 > 103586 SICHERUNGSLACK 603 10ML PDF資料下載
參數資料
| 型號： | 103586 |
| 英文描述： | SICHERUNGSLACK 603 10ML |
| 中文描述： | SICHERUNGSLACK 603毫升 |
| 文件頁數： | 2/2頁 |
| 文件大?。?/td> | 31K |
| 代理商： | 103586 |
TDS 603 October 1995
Loctite is a Registered Trademark of Loctite Corporation, Hartford, CT 06106
PERFORMANCE OF CURED MATERIAL
(After 24 hr at 22
°C on steel)
Typical
Value
Range
Shear Strength, ISO 10123, N/mm
26
20 to 32
(psi)
(3770)
(2900 to 4600)
Shear Strength, DIN 54452, N/mm
20.5
16 to 25
(psi)
(3000)
(2300 to 3600)
TYPICAL ENVIRONMENTAL RESISTANCE
Test Procedure :
Shear Strength, ISO 10123
Substrate:
Steel Pins and Collars
Cure procedure:
1 week at 22
°C
Hot Strength
Tested at temperature.
0
50
100
150
0
25
50
75
100
Temperature, °C
%
R
T
Stre
ngth
Heat Ageing
Aged at temperature indicated and tested at 22
°C.
0
1,000
2,000
3,000
4,000
5,000
0
25
50
75
100
125
Hours
%
Init
ia
lStre
ngth
,at
R
T
120°C
150°C
Chemical / Solvent Resistance
Aged under conditions indicated and tested at 22
°C.
Solvent
Temp.
% Initial Strength retained at
100 hr
500 hr
1000 hr
Motor Oil
125
°C
100
Unleaded Petrol
22
°C
100
90
85
Brake Fluid
22
°C
100
90
80
Water/Glycol (50%/50%)
87
°C
100
90
80
Ethanol
22
°C
100
75
Acetone
22
°C
90
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidising materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
Where aqueous washing systems are used to clean the
surfaces
before
bonding,
it
is
important
to
check
for
compatibility of the washing solution with the adhesive.
In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
For best performance surfaces should be clean and free of
grease. Ensure joint is completely filled with adhesive. For slip
fitted assemblies this is achieved by applying adhesive around
the pin and the leading edge of the collar and using a rotating
motion during assembly to ensure good coverage. For press
fitted assemblies adhesive should be applied thoroughly to
both bond surfaces and assembled at high press on rates. For
shrink fitted assemblies the adhesive should be coated onto
the pin, the collar should then be heated to create sufficient
clearance for free assembly. Parts should not be disturbed until
sufficient handling strength is achieved. This grade has the
ability to cure through thin films of most protective oils. Some
oils contain rust inhibitors (e.g. sodium nitrate) which will
chemically inhibit the adhesive cure.
Cure speed and final
strength on oiled surfaces will be affected, depending on the
type and amount of oil used. For more detailed information on
using retaining adhesives contact your local technical service
centre.
Storage
Product shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8
°C to 28°C
(46
°F to 82°F) unless otherwise labelled. Optimal storage is at
the lower half of this temperature range.
To prevent
contamination of unused product, do not return any material to
its original container. For further specific shelf life information,
contact your local Technical Service Centre.
Data Ranges
The data contained herein may be reported as a typical value
and/or range (based on the mean value
±2 standard
deviations).
Values are based on actual test data and are
verified on a periodic basis.
Note
The data contained herein are furnished for information only
and are believed to be reliable.
We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof.
In light of the foregoing, Loctite Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a particular
purpose, arising from sale or use of Loctite Corporation’s
products. Loctite Corporation specifically disclaims any liability
for consequential or incidental damages of any kind, including
lost profits.
The discussion herein of various processes or
compositions is not to be interpreted as representation that
they are free from domination of patents owned by others or as
a licence under any Loctite Corporation patents that may cover
such processes or compositions.
We recommend that each
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.
相關PDF資料 |
PDF描述 |
|---|---|
| 1035 | MULTIOEL 5 56.5 LITER SPR FLASCHE |
| 1039157 | FIBER OPTIC SPLITTER/COUPLER, 1X2PORT, PANEL MOUNT, W/O CONNECTOR |
| 1039159 | FIBER OPTIC SPLITTER/COUPLER, 1X2PORT, PANEL MOUNT, LC CONNECTOR |
| 103MG8 | SPECIALTY ANALOG CIRCUIT, XSS |
| 106MG10 | SPECIALTY ANALOG CIRCUIT, XSS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1035860000 | 制造商:Weidmuller 功能描述:CONN HEADER 18POS 3.81MM VERT BK |
| 103586-107 | |
| 103586-12 | 功能描述:SHL RECP ASSY 制造商:te connectivity deutsch connectors 系列:* 零件狀態:在售 標準包裝:1 |
| 103586-58 | |
| 103587 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SICHERUNGSLACK 603 50ML |
發布緊急采購，3分鐘左右您將得到回復。