- 您現在的位置：買賣IC網 > PDF目錄351539 > 10TA00418 WINKELSCHWENKVERSCHRAUB 4MM G 0.125 PDF資料下載
參數資料
| 型號： | 10TA00418 |
| 英文描述： | WINKELSCHWENKVERSCHRAUB 4MM G 0.125 |
| 中文描述： | WINKELSCHWENKVERSCHRAUB毫米摹0.125 |
| 文件頁數： | 17/17頁 |
| 文件大小： | 269K |
| 代理商： | 10TA00418 |
Philips Semiconductors Programmable Logic Devices
Product specification
10H20EV8/10020EV8
ECL programmable array logic
October 22, 1993
121
AC TEST CIRCUIT
PULSE
GENERATOR
SCOPE
RT
L1
L3
VCC
VCO1
VCO2
VEE
SCOPE
L2
RT
CL
I1
I11
CLK/I12
FM
FN
FX
FY
DUT
+2.0V + 0.010V
–2.5V + 0.010V FOR 10020EV8
–3.2V + 0.010V FOR 10H20EV8
25
F
0.01
F
NOTES:
1. Use decoupling capacitors of 0.1
F and 25F from GND to VCC, and 0.01F and 25F from GND to VEE (0.01 and 0.1F capacitors
should be NPO Ceramic or MLC type). Decoupling capacitors should be placed as close as physically possible to the DUT and lead
length should be kept to less than 1/4 inch (6mm).
2. All unused inputs should be connected to either HIGH or LOW state consistent with the LOGIC function required.
3. All unused outputs are loaded with 50
to GND.
4. L1 and L2 are equal length 50 impedance lines. L3, the distance from the DUT pin to the junction of the cable from the Pulse
Generator and the cable to the Scope, should not exceed 1/4 inch (6mm).
5. RT = 50 terminator internal to Scope.
6. The unmatched wire stub between coaxial cable and pins under test must be less than 1/4 inch (6mm) long for proper test.
7. CL = Fixture and stray capacitance ≤ 3pF.
8. Any unterminated stubs connected anywhere along the transmission line between the Pulse Generator and the DUT or between the
DUT and the Scope should not exceed 1/4 inch (6mm) in length (refer to section on AC setup procedure).
9. All 50
resistors should have tolerance of ± 1% or better.
10. Test procedures are shown for only one input or set of input conditions. Other inputs are tested in the same manner.
25
F
0.1
F
相關PDF資料 |
PDF描述 |
|---|---|
| 10TA00618 | WINKELSCHWENKVERSCHRAUB 6MM G 0.125 |
| 10TA00828 | WINKELSCHWENKVERSCHRAUB 8MM G 0.25 |
| 10TA01038 | WINKELSCHWENKVERSCHRAUB 10MM G 0.375 |
| 10TA01248 | WINKELSCHWENKVERSCHRAUB 12MM G 0.5 |
| 10TR20 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 10TA00618 | 制造商:NORGREN 功能描述:REGULATOR BANJO 6MM 制造商:NORGREN 功能描述:REGULATOR, BANJO, 6MM 制造商:NORGREN 功能描述:REGULATOR, BANJO, 6MM; Operating Pressure Max:18bar; Operating Temperature Min:-20C; Operating Temperature Max:80C; SVHC:No SVHC (18-Jun-2012); External Diameter:6mm; Operating Temperature Range:-20C to +80C; Thread Size:1/8 BSP;;RoHS Compliant: NA |
| 10TA00828 | 制造商:NORGREN 功能描述:REGULATOR BANJO 8MM |
| 10TA023 | 制造商:Distributed By MCM 功能描述:Din Plug to RCA Cable |
| 10TA067-1 | 制造商:Distributed By MCM 功能描述:1 Ft Gold Plated RCA to RCA Patch Cables |
| 10TA104A-2M | 制造商:SPC Multicomp 功能描述:LEAD IEC 10A BLACK 2M 制造商:SPC Multicomp 功能描述:LEAD, IEC, 10A, BLACK, 2M 制造商:SPC Multicomp 功能描述:LEAD, IEC, 10A, BLACK, 2M, Connector Type A:IEC 60320 C13, Connector Type B:Wire, Voltage Rating:250V, Current Rating:10A, Cable Length - Imperial:6.5ft, Cable Length - Metric:2m, Jacket Colour:Black, Cable Assembly Type:Power, Cable, RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。