- 您現在的位置：買賣IC網 > PDF目錄69562 > 12061A220JAT2A KONDENSATOR 22PF 100V 10ST PDF資料下載
參數資料
| 型號： | 12061A220JAT2A |
| 英文描述： | KONDENSATOR 22PF 100V 10ST |
| 中文描述： | KONDENSATOR 22PF 100V的10ST |
| 文件頁數： | 18/46頁 |
| 文件大小： | 659K |
| 代理商： | 12061A220JAT2A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
24
General Specifications
Mechanical
Specification
No evidence of peeling of end terminal
Measuring Conditions
After soldering devices to circuit board apply 5N
(0.51kg f) for 10 ± 1 seconds, please refer to Figure 1.
Specification
Appearance:
No visual defects
Capacitance
Within specified tolerance
Q, Tan Delta
To meet initial requirement
Insulation Resistance
C0G (NP0), X7R
Initial Value x 0.3
Z5U, Y5V
Initial Value x 0.1
Measuring Conditions
Vibration Frequency
10-2000 Hz
Maximum Acceleration
20G
Swing Width
1.5mm
Test Time
X, Y, Z axis for 2 hours each, total 6 hours of test
END TERMINATION ADHERENCE
RESISTANCE TO VIBRATION
Specification
95% of each termination end should be covered with
fresh solder
Measuring Conditions
Dip device in eutectic solder at 230 ± 5°C for
2 ± .5 seconds
Figure 2. Bend Strength
Figure 1.
Terminal Adhesion
SOLDERABILITY
Specification
Appearance:
No visual defects
Capacitance Variation
C0G (NP0): ± 5% or ± .5pF, whichever is larger
X7R:
≤ ± 12%
Z5U:
≤ ± 30%
Y5V:
≤ ± 30%
Insulation Resistance
C0G (NP0):
≥ Initial Value x 0.3
X7R:
≥ Initial Value x 0.3
Z5U:
≥ Initial Value x 0.1
Y5V:
≥ Initial Value x 0.1
Measuring Conditions
Please refer to Figure 2
Deflection:
2mm
Test Time:
30 seconds
BEND STRENGTH
Specification
Appearance:
No serious defects, <25% leaching of either end
terminal
Capacitance Variation
C0G (NP0): ± 2.5% or ± 2.5pF, whichever is greater
X7R:
≤ ± 7.5%
Z5U:
≤ ± 20%
Y5V:
≤ ± 20%
Q, Tan Delta
To meet initial requirement
Insulation Resistance
To meet initial requirement
Dielectric Strength
No problem observed
Measuring Conditions
Dip device in eutectic solder at 260°C, for 1 minute.
Store at room temperature for 48 hours (24 hours for
C0G (NP0)) before measuring electrical parameters.
Part sizes larger than 3.20mm x 2.49mm are reheated
at 150°C for 30 ±5 seconds before performing test.
RESISTANCE TO SOLDER HEAT
Speed = 1mm/sec
R340mm
Supports
2mm
Deflection
45mm
5N FORCE
DEVICE UNDER TEST
TEST BOARD
相關PDF資料 |
PDF描述 |
|---|---|
| 12061A220J-MR | CAP. 22PF MINIREEL 500PCS |
| 12061A221JAT2A | KONDENSATOR 220PF 100V 10ST |
| 12061A221J-MR | CAP. 220PF MINIREEL 500PCS |
| 12061A222J-MR | CAP. 2.2NF MINIREEL 500PCS |
| 12061A330JAT2A | KONDENSATOR 33PF 100V 10ST |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 12061A220JAT2A/4K | 制造商:AVX Corporation 功能描述:CAP CER 22PF 100V 5% NP0 1206 |
| 12061A220JAT4A | 功能描述:多層陶瓷電容器MLCC - SMD/SMT 22pF 100volts 5% C0G RoHS:否 制造商:American Technical Ceramics (ATC) 電容:10 pF 容差:1 % 電壓額定值:250 V 溫度系數/代碼:C0G (NP0) 外殼代碼 - in:0505 外殼代碼 - mm:1414 工作溫度范圍:- 55 C to + 125 C 產品:Low ESR MLCCs 封裝:Reel |
| 12061A220JAT4A/20K | 制造商:AVX Corporation 功能描述:CAP CER 22PF 100V 5% NP0 1206 |
| 12061A220JATMA | 制造商:AVX Corporation 功能描述: |
| 12061A220J-MR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CAP. 22PF MINIREEL 500PCS |
發布緊急采購，3分鐘左右您將得到回復。