- 您現在的位置：買賣IC網 > PDF目錄222090 > 1339-31DCGI8 (INTEGRATED DEVICE TECHNOLOGY INC) 1 TIMER(S), REAL TIME CLOCK, PDSO8 PDF資料下載
參數資料
| 型號： | 1339-31DCGI8 |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘/數據恢復及定時提取 |
| 英文描述： | 1 TIMER(S), REAL TIME CLOCK, PDSO8 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, SOIC-8 |
| 文件頁數： | 26/26頁 |
| 文件大?。?/td> | 330K |
| 代理商： | 1339-31DCGI8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁
IDT1339
REAL-TIME CLOCK WITH SERIAL I2C INTERFACE
RTC
IDT
REAL-TIME CLOCK WITH SERIAL I2C INTERFACE
9
IDT1339
REV N 060311
Table 5. SQW/INT Output
Bit 2: Interrupt Control (INTCN). This bit controls the relationship between the two alarms and the interrupt output
pins. When the INTCN bit is set to logic 1, a match between the timekeeping registers and the alarm 1 or alarm 2
registers activate the SQW/INT pin (provided that the alarm is enabled). When the INTCN bit is set to logic 0, a
square wave is output on the SQW/INT pin. This bit is set to logic 0 when power is first applied.
Bit 1: Alarm 2 Interrupt Enable (A2IE). When set to a logic 1, this bit permits the Alarm 2 Flag (A2F) bit in the
status register to assert SQW/INT (when INTCN = 1). When the A2IE bit is set to logic 0 or INTCN is set to logic 0,
the A2F bit does not initiate an interrupt signal. The A2IE bit is disabled (logic 0) when power is first applied.
Bit 0: Alarm 1 Interrupt Enable (A1IE). When set to logic 1, this bit permits the Alarm 1 Flag (A1F) bit in the status
register to assert SQW/INT (when INTCN = 1). When the A1IE bit is set to logic 0 or INTCN is set to logic 0, the A1F
bit does not initiate an interrupt signal. The A1IE bit is disabled (logic 0) when power is first applied.
Status Register (0Fh)
Bit 7: Oscillator Stop Flag (OSF). A logic 1 in this bit indicates that the oscillator either is stopped or was stopped
for some period of time and may be used to judge the validity of the clock and date data. This bit is edge triggered
and is set to logic 1 when the oscillator stops. The following are examples of conditions that can cause the OSF bit
to be set:
1) The first time power is applied.
2) The voltage on both VCC and VBACKUP are insufficient to support oscillation.
3) The EOSC bit is turned off.
4) External influences on the crystal (e.g., noise, leakage, etc.).
This bit remains at logic 1 until written to logic 0. This bit can only be written to a logic 0.
Bit 1: Alarm 2 Flag (A2F). A logic 1 in the Alarm 2 Flag bit indicates that the time matched the alarm 2 registers. If
the A2IE bit is a logic 1 and the INTCN bit is set to a logic 1, the SQW/INT pin is also asserted. A2F is cleared when
written to logic 0. This bit can only be written to logic 0. Attempting to write to logic 1 leaves the value unchanged.
Bit 0: Alarm 1 Flag (A1F). A logic 1 in the Alarm 1 Flag bit indicates that the time matched the alarm 1 registers. If
the A1IE bit is a logic 1 and the INTCN bit is set to a logic 1, the SQW/INT pin is also asserted. A1F is cleared when
written to logic 0. This bit can only be written to logic 0. Attempting to write to logic 1 leaves the value unchanged.
INTCN
RS2
RS1
SQW/INT Output
A2IE
A1IE
00
0
1 Hz
X
0
1
4.096 kHz
X
0
1
0
8.192 kHz
X
0
1
32.768 kHz
X
1X
X
A1F
01
1X
X
A2F
10
1X
X
A2F + A1F
11
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
OSF
00000
A2F
A1F
相關PDF資料 |
PDF描述 |
|---|---|
| 13715-806-XTD | 300 MHz, OTHER CLOCK GENERATOR, PDSO16 |
| 1374610-3 | INTERCONNECTION DEVICE |
| 1376137-1 | POWER CONNECTOR |
| 1380B-8 | BRASS, GOLD FINISH, PCB TERMINAL |
| 1390D-17 | BRASS, PCB TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1339-31DVGI | 功能描述:實時時鐘 實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| 1339-31DVGI8 | 功能描述:實時時鐘 實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| 133933 | 制造商:ERNI Electronics 功能描述:133933 / MODULAR JACK |
| 133934 | 制造商:ERNI Electronics 功能描述:Conn Telephone/Telecom F 8 POS 2.54mm Solder ST Thru-Hole 8 Terminal 1 Port Tray Cat 5 |
| 1339342-1 | 功能描述:集管和線殼 1 Pair Double Red Pivot Conn RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
發布緊急采購，3分鐘左右您將得到回復。