- 您現在的位置：買賣IC網 > PDF目錄68784 > 144P502.58.FAR UNIVERSAL JOINT PDF資料下載
參數資料
| 型號： | 144P502.58.FAR |
| 英文描述： | UNIVERSAL JOINT |
| 中文描述： | 萬向節 |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 260K |
| 代理商： | 144P502.58.FAR |
0.84
0.75
0.63
Correction Factors
Working
Angle
10°
0.10
type HS, plain bearings – 1500 rpm max
selecting joint size
The correct joint size for a given application can be determined after
establishing the following criteria:
Torque or power to be transmitted
Speed of rotation
Maximum working angle
Fluctuations in load or prime mover output
using the nomogram
The nomogram is expressed Nm and is valid for the continuous
transmission of a constant or near constant load where the product of
speed (rpm)
× working angle exceeds 300. The curves are valid for
working angles up to 5°. Where use is intermittent, the stated values for
transmissible torque can be increased by 20% or conversely, the
calculated values in the following examples could be reduced by 16%.
In marginal cases, this would allow the selection of a smaller joint.
In addition to torque and speed of rotation, the working angle of the
joint has a bearing on its selection. The larger the working angle, the
higher the ‘effective’ load through the joint.
The factors tabled below will make the necessary correction as shown
in the following examples.
If converting from other units:
1 kW
= 1.341 HP
1 lbf ft = 1.356 Nm
Example 1
Transmitted torque
50lbf ft or (68 Nm)
Speed of rotation
500 rpm
Working angle
20°
Correction factor (from table)
0.75
∴ corrected torque = 68
=
91 Nm
0.75
Select the joint with the performance curve at or immediately above the
point of intersection of the horizontal corresponding to 91 Nm and the
vertical corresponding to 500 rpm, i.e. Joint Size 40. Note that the
length of the joint has no bearing on this calculation.
Example 2
Power rating
3.5 HP or (2.6 kW)
Speed of rotation
400 rpm
Working angle
30°
Correction factor (from table)
0.45
∴ corrected torque = 3.5
=
7.8 HP or (5.8 kW)
0.45
The power rating (HP or kW) must first be resolved to torque x rpm in
order to address the nomogram.
i.e. torque (Nm)
=
712
× HP or 9550 × kW
rpm
=
712
× 7.8
400
=
139 Nm
Select the joint with the performance curve at or immediately above the
point of intersection of the horizontal corresponding to 139 Nm and the
vertical corresponding to 400 rpm, i.e. Joint Size 50. Once again, the
length of the joint has no bearing on this calculation.
Correction
Factor
0.92
0.45
0.30
15°
20°
25°
30°
35°
40°
()
Low Speed/Low Working Angle
If the product of speed (rpm)
× working angle is less than 300 the
following method will determine an appropriate joint size.
1. Establish the torque in Nm
2. Determine the maximum working angle of the joint
3. Substitute these values in the corresponding formula:
For intermittent use
500
× torque
(100 – working angle)
For continuous use
600
× torque
(100 – working angle)
4. Select a joint with a static break torque in excess of the figure
obtained.
Example 3
Transmitted torque
50 Nm
Speed of rotation
Manual (intermittent)
Max. Working angle
25°
∴ torque rating
=
500
× 50
(100 – 25)
=
25000
75
=
333 Nm
Type HS joint size 32 (static torque 380 Nm) or type HE joint size 40
(static torque 650 Nm) should be selected.
500
400
300
200
100
SIZE 13
SIZE 16
SIZE 20
SIZE 25
SIZE 32
SIZE 40
SIZE 50
SIZE 63
90
80
70
60
50
40
30
20
10
9
8
7
6
4
2
5
3
1
100
200
300
400
600
800
1000
2000
RPM
T
o
rque
(Nm)
PERFORMANCE DATA (H SERIES)
(Please note that the nomograms do not apply to joints
assembled as telescopic drive shafts)
16
Tel: +44 (0)1992 509888
2
相關PDF資料 |
PDF描述 |
|---|---|
| 144P632.63.FAR | UNIVERSAL JOINT |
| 146P161.28.FAR | UNIVERSAL JOINT |
| 146P201.32.FAR | UNIVERSAL JOINT |
| 146P251.35.FAR | UNIVERSAL JOINT |
| 146P321.42.FAR | UNIVERSAL JOINT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 144P632.63.FAR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UNIVERSAL JOINT |
| 144-PGM12001-41 | 制造商:Aries Electronics Inc 功能描述:PIN GRID ARRAY SOCKET/HDR .100 |
| 144-PGM12001-51 | 制造商:Aries Electronics Inc 功能描述:PIN GRID ARRAY SOCKET/HDR .100 |
| 144-PGM13003-30 | 功能描述:IC 與器件插座 PIN GRID ARRAY WIRE WRAP 144 PINS RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 144-PGM13095-10 | 制造商:Aries Electronics Inc 功能描述:PIN GRID ARRAY SOCKET/HDR .100 |
發布緊急采購，3分鐘左右您將得到回復。