參數資料
型號： 20-101-0303
廠商： Rabbit Semiconductor
文件頁數： 117/126頁
文件大小： 0K
描述： SMARTSCREEN OP7100 W/TOUCHSCREEN
標準包裝： 1
顯示器類型： STN - 超扭轉向列，帶觸摸面板
可視范圍： 121.00mm L x 91.00mm W
背光： CCFL - 白
點象素： 320 x 240（QVGA）
接口： 串行
點間距： 0.36mm x 0.36mm
產品目錄頁面： 618 (CN2011-ZH PDF)
其它名稱： 20-101-0303-ND
20-101-303
20-101-303-ND
316-1175
OP7100
90
Troubleshooting
Out of the Box
Check the items mentioned in this section before starting development.
Verify that the OP7100 runs in standalone mode before connecting any
devices.
Verify that the entire host system has good, low-impedance, separate
grounds for analog and digital signals. The OP7100 might be connected
between the host PC and another device. Any differences in ground
potential from unit to unit can cause serious problems that are hard to
diagnose.
Do not connect analog ground to digital ground anywhere.
Double-check the connecting ribbon cables to ensure that all wires go
to the correct screw terminals on the OP7100.
Verify that the host PC’s COM port works by connecting a good serial
device to the COM port. Remember that COM1/COM3 and COM2/
COM4 share interrupts on a PC. User shells and mouse drivers, in
particular, often interfere with proper COM port operation. For
example, a mouse running on COM1 can preclude running Dynamic C
on COM3.
Use the supplied Rabbit Semiconductor power supply. If another power
supply must be used, verify that it has enough capacity and filtering to
support the OP7100.
Use the supplied Rabbit Semiconductor cables. The most common fault
of user-made cables is failure to properly assert CTS. Without CTS
being asserted, theOP7100’s RS-232 port will not transmit. Assert CTS
by either connecting the RTS signal of the PC’s COM port or looping
back the OP7100’s RTS.
Experiment with each peripheral device connected to the OP7100 to
determine how it appears to the OP7100 when powered up, powered
down, and/or when its connecting wiring is open or shorted.
The frame ground and 0 V are connected internally via a jumper on
header JP5. Remove the jumper if this connection causes problems or
is otherwise not required.
相關PDF資料
PDF描述
TPSW107M004R0100 CAP TANT 100UF 4V 20% 2312
GLK24064-25-VPT LCD GRAPHIC DISPL 240X64 Y/G BK
MK-GT380N KIT MODULE 3.8" MONOCHROME DISP
MK-GT380T KIT MODULE 3.8" TRANSFLECTV DISP
CWX823-060.0M OSC 60.0000MHZ 3.3V +-50PPM SMD
相關代理商/技術參數
參數描述
20-101-0343 功能描述:電纜組件 BL1800 proto board RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規（AWG）:20, 28 長度:0.305 m 顏色:Black, Red
20-101-0356 功能描述:單板計算機 BL1800 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0357 功能描述:單板計算機 BL1810 SINGLE BOARD COMPUTER RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0358 功能描述:單板計算機 BL1820 RoHS:否 制造商:Ampro By ADLINK 外觀尺寸:EPIC 處理器類型:Intel Atom D510 頻率:1.66 GHz 存儲容量:2 GB (max) 存儲類型:DDR2, L2 Cache 接口類型:Ethernet, PS/2, SATA, Serial, USB 工作電源電壓:5 V, 12 V 功耗:13 W 最大工作溫度:+ 70 C 尺寸:165.1 mm x 114.3 mm
20-101-0383 功能描述:模塊化系統 - SOM RCM2020 RabbitCore RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*