- 您現在的位置：買賣IC網 > PDF目錄3912 > 20-101-0435 (Rabbit Semiconductor)MODULE RABBITCORE RCM2110 PDF資料下載
參數資料
| 型號： | 20-101-0435 |
| 廠商： | Rabbit Semiconductor |
| 文件頁數： | 31/100頁 |
| 文件大小： | 0K |
| 描述： | MODULE RABBITCORE RCM2110 |
| 標準包裝： | 1 |
| 系列： | RabbitCore® |
| 模塊/板類型： | MPU 核心模塊 |
| 適用于相關產品： | RCM2110 |
| 產品目錄頁面： | 620 (CN2011-ZH PDF) |
| 其它名稱： | 316-1086 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
30
RabbitCore RCM2100
Once you have removed the 0
resistor “jumper,” R5, use a screw in the position indicated
in Figure 9 to attach the RCM2100 board to the chassis ground, thereby grounding the trans-
former/connector assembly.
Figure 9. R5 and Chassis Ground Locations
The RCM2100 is available in quantity without the transformer/connector assembly and
the ACT and LNK LEDs (shown to the right of the transformer/connector assembly in
Figure 9 above) installed. The Ethernet signals and the LED control signals are then avail-
able on header J3 installed on the bottom side of the board for this option, and J3 may then
be plugged in to the rest of the system. An Ethernet transformer and LEDs should be
included on the board that the modified RCM2100 is plugged into.
NOTE: Contact your Rabbit Semiconductor Sales Representative for quantity and pricing
information related to this option.
4.2.3 Programming Port
The RCM2100 has a 10-pin program header labeled J5. The programming port uses the
Rabbit 2000’s Serial Port A for communication. Dynamic C uses the programming port to
download and debug programs.
The programming port is also used for the following operations.
Cold-boot the Rabbit 2000 after a reset.
Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Resistor
R5
Insert screw with ring
terminal and ground
other end of wire to
chassis
相關PDF資料 |
PDF描述 |
|---|---|
| 345-030-527-801 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25640N-10SI-2.7 | IC EEPROM 64KBIT 3MHZ 8SOIC |
| 345-030-527-204 | CARDEDGE 30POS DUAL .100 GREEN |
| AT25640-10PI-2.7 | IC EEPROM 64KBIT 3MHZ 8DIP |
| 345-030-527-202 | CARDEDGE 30POS DUAL .100 GREEN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 20-101-0436 | 功能描述:模塊化系統 - SOM RCM2120 RabbitCore Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0437 | 功能描述:子卡和OEM板 SR9205 16 in/8 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| 20-101-0439 | 功能描述:模塊化系統 - SOM SR9215 SRC 8IN 16OUT RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| 20-101-0440 | 功能描述:模塊配件 SR9510 Relay 8 RoHS:否 制造商:Lantronix 產品: 用于: |
| 20-101-0444 | 功能描述:子卡和OEM板 SR9320 A/D 4-20mA RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
發布緊急采購，3分鐘左右您將得到回復。