Power Connection. A 3-pin header is provided for connection " />
參數資料
型號： 20-101-0436
廠商： Rabbit Semiconductor
文件頁數： 78/100頁
文件大?。?/td> 0K
描述： MODULE RABBITCORE RCM2120
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM2120
產品目錄頁面： 620 (CN2011-ZH PDF)
其它名稱： 316-1087
User’s Manual
73
B.1.1 Prototyping Board Features
Power Connection. A 3-pin header is provided for connection of a power supply. Note that it is sym-
metrical, with both outer pins connected to ground and the center pin connected to the raw V+ input. The
cable of the wall transformer provided with the North American version of the Development Kit ends in
a connector that is correctly connected in either orientation.
Users providing their own power supply should ensure that it delivers 9–24 V DC at not less than 500
mA. The voltage regulator will get warm in use, but lower supply voltages will reduce thermal dissipa-
tion from the device.
Regulated Power Supply. The raw DC voltage provided at the POWER IN jack is routed to a 5 V
linear voltage regulator, which provides stable power to the RCM2100 module and the Prototyping
Board. A Shottky diode protects the power supply against damage from reversed raw power connections.
Power LED. The power LED lights whenever power is connected to the Prototyping Board.
Reset Switch. A momentary-contact, normally open switch is connected directly to the RCM2100’s
/RES_IN pin. Pressing the switch forces a hardware reset of the system.
I/O Switches & LEDs. Two momentary-contact, normally open switches are connected to the PB2 and
PB3 pins of the RCM2100 module, and may be read as inputs by sample applications.
Two LEDs are connected to the PA0 and PA1 pins of the module, and may be driven as output indicators
by sample applications. (Two more LEDs, driven by PA2 and PA3, may be added to the Prototyping
Board for additional outputs.)
All the LEDs are connected through JP1, which has traces shorting adjacent pads together. These traces
may be cut to disconnect the LEDs, and an 8-pin header soldered into JP1 to permit their selective recon-
nection with jumpers. See Figure B-4 for details.
Expansion Areas. The Prototyping Board is provided with several unpopulated areas for expansion of
I/O and interfacing capabilities. See the next section for details.
Prototyping Area. A generous prototyping area has been provided for the installation of through-hole
components. Vcc (5 V DC) and Ground buses run around the edge of this area. An area for surface-
mount devices is provided to the right of the through-hole area. (Note that there are SMT device pads on
both top and bottom of the Prototyping Board.)
相關PDF資料
PDF描述
20-101-0404 MODULE RABBITCORE RCM2000
345-030-540-204 CARDEDGE 30POS DUAL .100 GREEN
345-030-540-202 CARDEDGE 30POS DUAL .100 GREEN
345-030-540-201 CARDEDGE 30POS DUAL .100 GREEN
046232412008800+ CONN FPC R ANGLE 1.0 MM 12 POS
相關代理商/技術參數
參數描述
20-101-0437 功能描述:子卡和OEM板 SR9205 16 in/8 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0439 功能描述:模塊化系統 - SOM SR9215 SRC 8IN 16OUT RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-0440 功能描述:模塊配件 SR9510 Relay 8 RoHS:否 制造商:Lantronix 產品: 用于:
20-101-0444 功能描述:子卡和OEM板 SR9320 A/D 4-20mA RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0445 功能描述:子卡和OEM板 SR9420 D/A Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*