- 您現在的位置：買賣IC網 > PDF目錄371393 > 24AA64-ESN (Microchip Technology Inc.) 64K I 2 C ⑩ CMOS Serial EEPROM PDF資料下載
參數資料
| 型號： | 24AA64-ESN |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 64K I 2 C ⑩ CMOS Serial EEPROM |
| 中文描述： | 64K的的I 2 C⑩的CMOS串行EEPROM |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 215K |
| 代理商： | 24AA64-ESN |
24AA64/24LC64
DS21189B-page 6
1998 Microchip Technology Inc.
5.0
DEVICE ADDRESSING
A control byte is the first byte received following the
start condition from the master device (Figure 5-1). The
control byte consists of a four bit control code; for the
24xx64 this is set as 1010 binary for read and write
operations. The next three bits of the control byte are
the chip select bits (A2, A1, A0). The chip select bits
allow the use of up to eight 24xx64 devices on the
same bus and are used to select which device is
accessed. The chip select bits in the control byte must
correspond to the logic levels on the corresponding A2,
A1, and A0 pins for the device to respond. These bits
are in effect the three most significant bits of the word
address.
The last bit of the control byte defines the operation to
be performed. When set to a one a read operation is
selected, and when set to a zero a write operation is
selected. The next two bytes received define the
address of the first data byte (Figure 5-2). Because
only A12...A0 are used, the upper three address bits
are don’t care bits. The upper address bits are trans-
ferred first, followed by the less significant bits.
Following the start condition, the 24xx64 monitors the
SDA bus checking the device type identifier being
transmitted. Upon receiving a 1010 code and appropri-
ate device select bits, the slave device outputs an
acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the 24xx64 will select a read or
write operation.
FIGURE 5-1:
CONTROL BYTE FORMAT
5.1
Contiguous Addressing Across
Multiple Devices
The chip select bits A2, A1, A0 can be used to expand
the contiguous address space for up to 512K bits by
adding up to eight 24xx64's on the same bus. In this
case, software can use A0 of the control byte as
address bit A13, A1 as address bit A14, and A2 as
address bit A15. It is not possible to sequentially read
across device boundaries.
FIGURE 5-2:
ADDRESS SEQUENCE BIT ASSIGNMENTS
1
0
1
0
A2
A1
A0
S
ACK
R/W
Control Code
Chip Select
Bits
Slave Address
Acknowledge Bit
Start Bit
Read/Write Bit
1
0
1
0
A
2
A
1
A
0R/W
X
X
X
A
11
A
10
A
9
A
7
A
0
A
8
A
12
CONTROL BYTE
ADDRESS HIGH BYTE
ADDRESS LOW BYTE
CONTROL
CODE
CHIP
SELECT
BITS
X = Don’t Care Bit
相關PDF資料 |
PDF描述 |
|---|---|
| 24AA64-EST | 64K I 2 C ⑩ CMOS Serial EEPROM |
| 24AA64-IP | 64K I 2 C ⑩ CMOS Serial EEPROM |
| 24AA64-ISM | 64K I 2 C ⑩ CMOS Serial EEPROM |
| 24AA64-ISN | 64K I 2 C ⑩ CMOS Serial EEPROM |
| 24AA64-IST | 64K I 2 C ⑩ CMOS Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24AA64F-I/MNY | 功能描述:電可擦除可編程只讀存儲器 64K 8KX8 1.8V SER EE IND 1/4AWP RPO RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24AA64F-I/MS | 功能描述:電可擦除可編程只讀存儲器 64K 8K X 8 1.8V SER EE IND 1/4AWP RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24AA64F-I/P | 功能描述:電可擦除可編程只讀存儲器 64K 8K X 8 1.8V SER EE IND 1/4AWP RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24AA64F-I/SM | 功能描述:電可擦除可編程只讀存儲器 64K 8K X 8 1.8V SER EE IND 1/4AWP RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24AA64F-I/SN | 功能描述:電可擦除可編程只讀存儲器 64K 8K X 8 1.8V SER EE IND 1/4AWP RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。