參數資料
型號: 24C00T-ESN
廠商: Microchip Technology Inc.
英文描述: 128 Bit I 2 C? Bus Serial EEPROM
中文描述: 128位的I 2 C?總線串行EEPROM
文件頁數: 6/18頁
文件大?。?/td> 264K
代理商: 24C00T-ESN
24AA00/24LC00/24C00
DS21178D-page 6
2003 Microchip Technology Inc.
5.0
DEVICE ADDRESSING
After generating a Start condition, the bus master
transmits a control byte consisting of a slave address
and a Read/Write bit that indicates what type of
operation is to be performed. The slave address for the
24XX00 consists of a 4-bit device code ‘
1010
’ followed
by three don't care bits.
The last bit of the control byte determines the operation
to be performed. When set to a one a read operation is
selected, and when set to a zero a write operation is
selected. (Figure 5-1). The 24XX00 monitors the bus
for its corresponding slave address all the time. It
generates an Acknowledge bit if the slave address was
true and it is not in a Programming mode.
FIGURE 5-1:
CONTROL BYTE FORMAT
6.0
WRITE OPERATIONS
6.1
Byte Write
Following the Start signal from the master, the device
code (4 bits), the don't care bits (3 bits), and the R/W bit
(which is a logic low) are placed onto the bus by the
master transmitter. This indicates to the addressed
slave receiver that a byte with a word address will
follow after it has generated an Acknowledge bit during
the ninth clock cycle. Therefore, the next byte transmit-
ted by the master is the word address and will be
written into the address pointer of the 24XX00. Only the
lower four address bits are used by the device, and the
upper four bits are don’t cares. The 24XX00 will
acknowledge the address byte and the master device
will then transmit the data word to be written into the
addressed memory location. The 24XX00 acknowl-
edges again and the master generates a Stop
condition. This initiates the internal write cycle, and
during this time the 24XX00 will not generate Acknowl-
edge signals (Figure 7-2). After a byte Write command,
the internal address counter will not be incremented
and will point to the same address location that was just
written. If a Stop bit is transmitted to the device at any
point in the Write command sequence before the entire
sequence is complete, then the command will abort
and no data will be written. If more than 8 data bits are
transmitted before the Stop bit is sent, then the device
will clear the previously loaded byte and begin loading
the data buffer again. If more than one data byte is
transmitted to the device and a Stop bit is sent before a
full eight data bits have been transmitted, then the
Write command will abort and no data will be written.
The 24XX00 employs a V
CC
threshold detector circuit
which disables the internal erase/write logic if the V
CC
is below 1.5V (24AA00 and 24LC00) or 3.8V (24C00)
at nominal conditions.
1
0
1
0
X
X
X
S
ACK
R/W
Device Select
Bits
Don’t Care
Bits
Slave Address
Acknowledge Bit
Start Bit
Read/Write Bit
相關PDF資料
PDF描述
24C00T-EST 128 Bit I 2 C? Bus Serial EEPROM
24C00T-IOT 128 Bit I 2 C? Bus Serial EEPROM
24AA014 1K I2C⑩ Serial EEPROM
24AA01 1K I2C Serial EEPROM
24AA01IP 1K/2K 1.8V I 2 C O Serial EEPROMs
相關代理商/技術參數
參數描述
24C00T-EST 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:128 Bit I 2 C? Bus Serial EEPROM
24C00T-I/MC 功能描述:電可擦除可編程只讀存儲器 16 byte 128 bit 5V SEE IND RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24C00T-I/MNY 功能描述:電可擦除可編程只讀存儲器 16 byte 128 bit 5V SEE IND RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24C00T-I/OT 功能描述:電可擦除可編程只讀存儲器 16byte 128kb 5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24C00T-I/OT-CUT TAPE 制造商:Microchip 功能描述:24C00 Series 128 bit (16 x 8) 5.5 V SMT I2C Bus Serial EEPROM - SOT-23-5