- 您現在的位置：買賣IC網 > PDF目錄371394 > 24C01B-ESN (Microchip Technology Inc.) 1K/2K 5.0V I 2 C ⑩ Serial EEPROM PDF資料下載
參數資料
| 型號： | 24C01B-ESN |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 1K/2K 5.0V I 2 C ⑩ Serial EEPROM |
| 中文描述： | 1K/2K 5.0VI 2葷⑩串行EEPROM |
| 文件頁數： | 5/12頁 |
| 文件大小： | 162K |
| 代理商： | 24C01B-ESN |
24C01B/02B
1997 Microchip Technology Inc.
Preliminary
DS21233A-page 5
3.6
Device Address
After generating a START condition, the bus master
transmits the slave address consisting of a 4-bit device
code (1010) for the 24C01B/02B, followed by three
don't care bits.
The eighth bit of slave address determines if the master
device wants to read or write to the 24C01B/02B
(Figure 3-2).
The 24C01B/02B monitors the bus for its correspond-
ing slave address all the time. It generates an acknowl-
edge bit if the slave address was true and it is not in a
programming mode.
FIGURE 3-2:
CONTROL BYTE
ALLOCATION
4.0
WRITE OPERATION
4.1
Byte Write
Following the start signal from the master, the device
code (4 bits), the don't care bits (3 bits), and the R/W
bit which is a logic low is placed onto the bus by the
master transmitter. This indicates to the addressed
slave receiver that a byte with a word address will follow
after it has generated an acknowledge bit during the
ninth clock cycle. Therefore the next byte transmitted
by the master is the word address and will be written
into the address pointer of the 24C01B/02B. After
receiving another acknowledge signal from the
24C01B/02B the master device will transmit the data
word to be written into the addressed memory location.
The 24C01B/02B acknowledges again and the master
generates a stop condition. This initiates the internal
write cycle, and during this time the 24C01B/02B will
not generate acknowledge signals (Figure 4-1).
4.2
Page Write
The write control byte, word address and the first data
byte are transmitted to the 24C01B/02B in the same
way as in a byte write. But instead of generating a stop
condition the master transmits up to eight data bytes to
the 24C01B/02B which are temporarily stored in the
on-chip page buffer and will be written into the memory
after the master has transmitted a stop condition. After
the receipt of each word, the three lower order address
pointer bits are internally incremented by one. The
higher order five bits of the word address remains con-
stant. If the master should transmit more than eight
words prior to generating the stop condition, the
address counter will roll over and the previously
received data will be overwritten. As with the byte write
operation, once the stop condition is received an inter-
nal write cycle will begin (Figure 4-2).
FIGURE 4-1:
BYTE WRITE
FIGURE 4-2:
PAGE WRITE
Operation
Control
Code
Chip
Select
R/W
Read
Write
1010
1010
XXX
XXX
1
0
X = Don’t care
R/W
A
1
0
1
0
X
X
X
READ/WRITE
START
SLAVE ADDRESS
S
P
S
T
A
R
T
S
T
O
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
A
C
K
A
C
K
A
C
K
CONTROL
BYTE
WORD
ADDRESS
DATA
S
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
S
T
A
R
T
S
T
O
P
CONTROL
BYTE
WORD
ADDRESS (n)
DATA n
DATAn + 7
DATAn + 1
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
相關PDF資料 |
PDF描述 |
|---|---|
| 24C02B | 1K/2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C02B-EP | 1K/2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C02B-ESN | 1K/2K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C01C | 1K 5.0V I 2 C ⑩ Serial EEPROM |
| 24C01C-IP | 1K 5.0V I 2 C ⑩ Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C01BP | 制造商:Microchip Technology Inc 功能描述:128 X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| 24C01BT-E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C⑩ Serial EEPROM |
| 24C01BT-E/SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K/2K 5.0V I2C⑩ Serial EEPROM |
| 24C01C | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K 5.0V I2C? Serial EEPROM |
| 24C01C/P | 功能描述:電可擦除可編程只讀存儲器 128x8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。