參數資料
型號: 24C02C-SN
廠商: Microchip Technology Inc.
英文描述: 2K 5.0V I 2 C ⑩ Serial EEPROM
中文描述: 2K 5.0VI 2葷⑩串行EEPROM
文件頁數: 9/12頁
文件大?。?/td> 162K
代理商: 24C02C-SN
24C02C
1997 Microchip Technology Inc.
Preliminary
DS21202A-page 9
8.0
READ OPERATIONS
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
slave address is set to one. There are three basic types
of read operations: current address read, random read,
and sequential read.
8.1
Current Address Read
The 24C02C contains an address counter that main-
tains the address of the last word accessed, internally
incremented by one. Therefore, if the previous read
access was to address n, the next current address read
operation would access data from address n + 1. Upon
receipt of the slave address with the R/W bit set to one,
the 24C02C issues an acknowledge and transmits the
eight bit data word. The master will not acknowledge
the transfer but does generate a stop condition and the
24C02C discontinues transmission (Figure 8-1).
8.2
Random Read
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
24C02C as part of a write operation. After the word
address is sent, the master generates a start condition
following the acknowledge. This terminates the write
operation, but not before the internal address pointer is
set. Then the master issues the control byte again but
with the R/W bit set to a one. The 24C02C will then
issue an acknowledge and transmits the eight bit data
word. The master will not acknowledge the transfer but
does generate a stop condition and the 24C02C dis-
continues transmission (Figure 8-2). After this com-
mand, the internal address counter will point to the
address location following the one that was just read.
8.3
Sequential Read
Sequential reads are initiated in the same way as a ran-
dom read except that after the 24C02C transmits the
first data byte, the master issues an acknowledge as
opposed to a stop condition in a random read. This
directs the 24C02C to transmit the next sequentially
addressed 8-bit word (Figure 8-3).
To provide sequential reads the 24C02C contains an
internal address pointer which is incremented by one at
the completion of each operation. This address pointer
allows the entire memory contents to be serially read
during one operation. The internal address pointer will
automatically roll over from address FF to address 00.
FIGURE 8-1:
CURRENT ADDRESS READ
FIGURE 8-2:
RANDOM READ
FIGURE 8-3:
SEQUENTIAL READ
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
P
S
S
T
O
P
CONTROL
BYTE
S
T
A
R
T
DATA
A
C
K
N
O
A
C
K
S
P
S
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
S
T
A
R
T
S
T
O
P
CONTROL
BYTE
A
C
K
WORD
ADDRESS (n)
CONTROL
BYTE
S
T
A
R
T
DATA (n)
A
C
K
A
C
K
N
O
A
C
K
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
CONTROL
BYTE
DATA n
DATA n + 1
DATA n + 2
DATA n + X
N
O
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
S
T
O
P
P
相關PDF資料
PDF描述
24C02C-ST 2K 5.0V I 2 C ⑩ Serial EEPROM
24C05LN 4K-Bit Standard 2-Wire Bus Interface Serial EEPROM
24C080-EP 8K/16K 5.0V SPI Bus Serial EEPROM
24C080-ESN 8K/16K 5.0V SPI Bus Serial EEPROM
24C080-IP 8K/16K 5.0V SPI Bus Serial EEPROM
相關代理商/技術參數
參數描述
24C02CST 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM
24C02C-ST 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 5.0V I 2 C ⑩ Serial EEPROM
24C02CT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 5.0V I2C Serial EEPROM
24C02CT/SN 功能描述:電可擦除可編程只讀存儲器 256x8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
24C02CT/SN-CUT TAPE 制造商:Microchip 功能描述:24C02 Series 2 Kbit (256 x 8) 5.5 V Surface Mount I2C Serial EEPROM - SOIC-8