- 您現在的位置：買賣IC網 > PDF目錄371396 > 24C65-ESM (Microchip Technology Inc.) 64K 5.0V I 2 C Smart Serial EEPROM PDF資料下載
參數資料
| 型號： | 24C65-ESM |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 64K 5.0V I 2 C Smart Serial EEPROM |
| 中文描述： | 64K的5.0VI 2葷智能串行EEPROM |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 120K |
| 代理商： | 24C65-ESM |
24C65
DS21058G-page 8
1996 Microchip Technology Inc.
define the number of blocks to be write protected. For
example, if three blocks are to be protected, the third
byte would be 10XX0011. After the third byte is sent to
the device, it will acknowledge and a STOP bit is then
sent by the master to complete the command.
During a normal write sequence, if an attempt is made
to write to a protected address, no data will be written
and the device will not report an error or abort the com-
mand. If a write command is attempted across a
secure boundary, unprotected addresses will be written
and protected addresses will not.
5.8
Security Configuration Read
The status of the secure portion of memory can be read
by using the same technique as programming this
option except the READ bit (bit 6) of the configuration
byte is set to a one. After the configuration byte is sent,
the device will acknowledge and then send two bytes of
data to the master just as in a normal read sequence.
The master must acknowledge the first byte and not
acknowledge the second, and then send a stop bit to
end the sequence. The upper four bits of both of these
bytes will always be read as '1's. The lower four bits of
the first byte contains the starting secure block. The
lower four bits of the second byte contains the number
of secure blocks. The default starting secure block is fif-
teen and the default number of secure blocks is zero
(Figure 8-1).
6.0
ACKNOWLEDGE POLLING
Since the device will not acknowledge during a write
cycle, this can be used to determine when the cycle is
complete (this feature can be used to maximize bus
throughput). Once the stop condition for a write com-
mand has been issued from the master, the device ini-
tiates the internally timed write cycle. ACK polling can
be initiated immediately. This involves the master send-
ing a start condition followed by the control byte for a
write command (R/W = 0). If the device is still busy with
the write cycle, then no ACK will be returned. If the
cycle is complete, then the device will return the ACK
and the master can then proceed with the next read or
write command. See Figure 6-1 for flow diagram.
FIGURE 6-1:
ACKNOWLEDGE POLLING
FLOW
Send
Write Command
Send Stop
Condition to
Initiate Write Cycle
Send Start
Send Control Byte
with R/W = 0
Did Device
Acknowledge
(ACK = 0)
Next
Operation
NO
YES
相關PDF資料 |
PDF描述 |
|---|---|
| 24C65-IP | 64K 5.0V I 2 C Smart Serial EEPROM |
| 24C65-ISM | 64K 5.0V I 2 C Smart Serial EEPROM |
| 24C65-P | 64K 5.0V I 2 C Smart Serial EEPROM |
| 24C65-SM | 64K 5.0V I 2 C Smart Serial EEPROM |
| 24CMD25 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24C65-I/P | 功能描述:電可擦除可編程只讀存儲器 8kx8 Smart RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24C65-I/P | 制造商:Microchip Technology Inc 功能描述:IC EEPROM SERIAL 64K 24C65 DIP8 |
| 24C65-I/PG | 功能描述:電可擦除可編程只讀存儲器 8kx8 Smart Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24C65I/SM | 制造商:Microchip Technology Inc 功能描述:Serial EEPROM, 8K x 8, 8 Pin, Plastic, SOP |
| 24C65-I/SM | 功能描述:電可擦除可編程只讀存儲器 8kx8 Smart RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。