- 您現在的位置：買賣IC網 > PDF目錄371397 > 24CO24-IST (Microchip Technology Inc.) 2K 2.5V I 2 C ⑩ Serial EEPROM PDF資料下載
參數資料
| 型號： | 24CO24-IST |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 2K 2.5V I 2 C ⑩ Serial EEPROM |
| 中文描述： | 2K 2.5VI 2葷⑩串行EEPROM |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 163K |
| 代理商： | 24CO24-IST |
24LC024/24LC025
1997 Microchip Technology Inc.
Preliminary
DS21210A-page 7
6.0
WRITE OPERATIONS
6.1
Byte Write
Following the start signal from the master, the device
code(4 bits), the chip select bits (3 bits), and the R/W
bit which is a logic low is placed onto the bus by the
master transmitter. The device will acknowledge this
control byte during the ninth clock pulse. The next byte
transmitted by the master is the word address and will
be written into the address pointer of the 24LC024/
24LC025. After receiving another acknowledge signal
from the 24LC024/24LC025 the master device will
transmit the data word to be written into the addressed
memory location. The 24LC024/24LC025 acknowl-
edges again and the master generates a stop condi-
tion. This initiates the internal write cycle, and during
this time the 24LC024/24LC025 will not generate
acknowledge signals (Figure 6-1). If an attempt is made
to write to the protected portion of the array when the
hardware write protection (24LC024 only) has been
enabled, the device will acknowledge the command but
no data will be written. The write cycle time must be
observed even if the write protection is enabled.
6.2
Page Write
The write control byte, word address and the first data
byte are transmitted to the 24LC024/24LC025 in the
same way as in a byte write. But instead of generating
a stop condition, the master transmits up to 15 addi-
tional data bytes to the 24LC024/24LC025 which are
temporarily stored in the on-chip page buffer and will be
written into the memory after the master has transmit-
ted a stop condition. After the receipt of each word, the
four lower order address pointer bits are internally
incremented by one. The higher order four bits of the
word address remains constant. If the master should
transmit more than 16 bytes prior to generating the stop
condition, the address counter will roll over and the pre-
viously received data will be overwritten. As with the
byte write operation, once the stop condition is received
an internal write cycle will begin (Figure 6-2). If an
attempt is made to write to the protected portion of the
array when the hardware write protection has been
enabled, the device will acknowledge the command but
no data will be written. The write cycle time must be
observed even if the write protection is enabled.
6.3
WRITE PROTECTION
The WP pin (available on 24LC024 only) must be tied
to V
CC
or V
SS
. If tied to V
CC
, the entire array will be write
protected. If the WP pin is tied to V
SS
, then write oper-
ations to all address locations are allowed.
FIGURE 6-1:
BYTE WRITE
FIGURE 6-2:
PAGE WRITE
S
T
A
R
T
S
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
S
T
A
R
T
S
T
O
P
CONTROL
BYTE
WORD
ADDRESS
DATA
A
C
K
A
C
K
A
C
K
S
P
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
CONTROL
BYTE
WORD
ADDRESS (n)
DATA n
DATA n + 15
S
T
O
P
A
C
K
A
C
K
A
C
K
A
C
K
A
C
K
DATA n +1
相關PDF資料 |
PDF描述 |
|---|---|
| 24CO24-P | 2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO24-SN | 2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO24-ST | 2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO25-IP | 2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO25-ISN | 2K 2.5V I 2 C ⑩ Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24CO24-P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO24-SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO24-ST | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO25-IP | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 2.5V I 2 C ⑩ Serial EEPROM |
| 24CO25-ISN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:2K 2.5V I 2 C ⑩ Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。