- 您現在的位置：買賣IC網 > PDF目錄371397 > 24LC01B-MT (Microchip Technology Inc.) 1K/2K I 2 C ⑩ Serial EEPROMs in ISO Micromodules PDF資料下載
參數資料
| 型號： | 24LC01B-MT |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 1K/2K I 2 C ⑩ Serial EEPROMs in ISO Micromodules |
| 中文描述： | 1K/2K的I 2 C⑩在ISO微型模塊串行EEPROM |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 451K |
| 代理商： | 24LC01B-MT |
24LC01B/02B Modules
DS21222A-page 2
1997 Microchip Technology Inc.
1.0
ELECTRICAL CHARACTERISTICS
1.1
Maximum Ratings*
V
All inputs and outputs w.r.t. V
Storage temperature .....................................-65C to +150C
Ambient temp. with power applied.................-65C to +125C
ESD protection on all pads.............................................
CC
...................................................................................7.0V
SS
................-0.6V to V
CC
+1.0V
≥
4 kV
*Notice:
may cause permanent damage to the device. This is a stress rat-
ing only and functional operation of the device at those or any
other conditions above those indicated in the operational listings
of this specification is not implied. Exposure to maximum rating
conditions for extended periods may affect device reliability.
Stresses above those listed under “Maximum ratings”
TABLE 1-1:
PAD FUNCTION TABLE
1.2
Pad Descriptions
1.2.1
SDA (Serial Data)
This is a bi-directional pad used to transfer addresses
and data into and data out of the device. It is an open
drain terminal, therefore the SDA bus requires a pull-up
resistor to V
CC
(typical 10 K
400 kHz).
For normal data transfer SDA is allowed to change only
during SCL low. Changes during SCL high are reserved
for indicating the START and STOP conditions.
for 100 kHz, 2 K
for
1.2.2
SCL (Serial Clock)
This input is used to synchronize the data transfer from
and to the device.
Name
Function
V
SDA
SCL
V
CC
SS
Ground
Serial Address/Data I/O
Serial Clock
+2.5V to 5.5V Power Supply
TABLE 1-1
DC CHARACTERISTICS
All Parameters apply across the recom-
mended operating ranges unless other-
wise noted.
Commercial (C):
Tamb = 0C to +70C, V
CC
= 2.5V to 5.5V
Parameter
Symbol
Min.
Max.
Units
Conditions
SCL and SDA pins:
High level input voltage
Low level input voltage
Hysteresis of Schmitt trigger inputs
Low level output voltage
V
V
IH
0.7 V
CC
V
V
V
V
(Note)
(Note)
Vcc
I
OL
= 3.0 mA, V
I
OL
= 2.1 mA, V
V
IN
= V
CC
V
OUT
= V
V
CC
= 5.0V (Note)
Tamb = 25C, f = 1 MHz
V
CC
= 5.5V, SCL = 400 kHz
V
CC
= 5.5V, SCL = 400 kHz
V
CC
= 5.5V, SDA = SCL = V
IL
0.3 V
CC
V
V
HYS
0.05 V
CC
—
0.40
≥
2.5V (Note)
OL
CC
CC
= 4.5V
= 2.5V
Input leakage current
Output leakage current
Pin capacitance (all inputs/outputs)
I
LI
-10
-10
—
10
10
10
μ
μ
pF
A
A
or V
or V
SS
I
LO
C
IN
C
OUT
Write
Read
I
CCS
CC
SS
,
Operating current
I
I
CC
—
—
—
3
1
mA
mA
μ
A
CC
Standby current
Note:
100
CC
This parameter is periodically sampled and not 100% tested.
相關PDF資料 |
PDF描述 |
|---|---|
| 24LC02B | 1K/2K I 2 C ⑩ Serial EEPROMs in ISO Micromodules |
| 24LC02B-MT | 1K/2K I 2 C ⑩ Serial EEPROMs in ISO Micromodules |
| 24LC01BMODULES | Stand-Alone OCV-Based Fuel Gauge |
| 24LC02BMODULES | Single/Dual/Triple/Quad DS3/E3 Single-Chip Transceivers |
| 24LC040-ESN | 4K SPI ⑩ Bus Serial EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24LC01BP | 制造商:MICRO CHIP 功能描述:* |
| 24LC01BSN | 制造商:MICRO CHIP 功能描述:New |
| 24LC01B-SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K I2Ca?￠ Serial EEPROM |
| 24LC01BT | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:1K I2C? Serial EEPROM |
| 24LC01BT/MS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM |
發布緊急采購，3分鐘左右您將得到回復。