- 您現在的位置：買賣IC網 > PDF目錄371399 > 24LC65-SM (Microchip Technology Inc.) 64K 2.5V I 2 C Smart Serial EEPROM PDF資料下載
參數資料
| 型號： | 24LC65-SM |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 64K 2.5V I 2 C Smart Serial EEPROM |
| 中文描述： | 64K的2.5VI 2葷智能串行EEPROM |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 106K |
| 代理商： | 24LC65-SM |
24LC65
DS21073E-page 4
1996 Microchip Technology Inc.
2.0
FUNCTIONAL DESCRIPTION
The 24LC65 supports a bidirectional two-wire bus and
data transmission protocol. A device that sends data
onto the bus is defined as transmitter, and a device
receiving data as receiver. The bus must be controlled
by a master device which generates the serial clock
(SCL), controls the bus access, and generates the
START and STOP conditions, while the 24LC65 works
as slave. Both master and slave can operate as trans-
mitter or receiver but the master device determines
which mode is activated.
3.0
BUS CHARACTERISTICS
The following
bus protocol
has been defined:
Data transfer may be initiated only when the bus is
not busy.
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition.
Accordingly, the following bus conditions have been
defined (Figure 3-1).
3.1
Bus not Busy (A)
Both data and clock lines remain HIGH.
3.2
Start Data Transfer (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
3.3
Stop Data Transfer (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations must be ended with a STOP condition.
3.4
Data Valid (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition. The number of
the data bytes transferred between the START and
STOP conditions is determined by the master device.
3.5
Acknowledge
Each receiving device, when addressed, is obliged to
generate an acknowledge after the reception of each
byte. The master device must generate an extra clock
pulse which is associated with this acknowledge bit.
A device that acknowledges must pull down the SDA
line during the acknowledge clock pulse in such a way
that the SDA line is stable LOW during the HIGH period
of the acknowledge related clock pulse. Of course,
setup and hold times must be taken into account. Dur-
ing reads, a master must signal an end of data to the
slave by NOT generating an acknowledge bit on the last
byte that has been clocked out of the slave. In this case,
the slave (24LC65) must leave the data line HIGH to
enable the master to generate the STOP condition.
Note:
The 24LC65 does not generate any
acknowledge bits if an internal program-
ming cycle is in progress.
FIGURE 3-1:
DATA TRANSFER SEQUENCE ON THE SERIAL BUS
(A)
(B)
(D)
(D)
(A)
(C)
START
CONDITION
ADDRESS OR
ACKNOWLEDGE
VALID
DATA
ALLOWED
TO CHANGE
STOP
CONDITION
SCL
SDA
相關PDF資料 |
PDF描述 |
|---|---|
| 24LCS21A | 1K 2.5V Dual Mode I 2 C Serial EEPROM |
| 24LCS21 | 1K 2.5V Dual Mode I 2 C Serial EEPROM |
| 24LCS41A | 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) |
| 24LCS41 | 1K/4K 2.5V Dual Mode, Dual Port IIC Serial EEPROM(1K/4K位,2.5V雙模式,雙端口IIC串行EEPROM) |
| 24LCS52 | Connectors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 24LC65T/SM | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC65T/SMG | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart Lead Free Package RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC65T-I/SM | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LC65T-I/SMG | 功能描述:電可擦除可編程只讀存儲器 8kx8 - 2.5V Smart Industrial Temp RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| 24LCS21A/P | 功能描述:電可擦除可編程只讀存儲器 2.5V Dual Mode RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。