參數資料
型號： 27010
廠商： Texas Instruments, Inc.
英文描述： Li-Ion AND Li-Pol BATTERY GAS GAUGE IC FOR PORTABLE APPLICATIONS (bqJUNIOR)
中文描述： 鋰離子和鋰聚合物電池電量監測計芯片的便攜式應用（bqJUNIOR）
文件頁數： 20/30頁
文件大?。?/td> 337K
代理商： 27010
www.ti.com
Taper Current (TAPER) — Address 0x7B
This register contains the enable bit for the capacity aging estimate and the charge taper current value. The
taper current value, in addition to battery voltage, is used to determine when the battery has reached a full
charge state. The equation for programming the taper current is:
TAPER[6-0] = Design Taper Current (mA) * R
S
(m
) / 228 μV
where R
S
is the value of the sense resistor used in the system.
TAPER[7] should be set to
1
to enable the automatic aging of the LMD full capacity value when there are no
learning cycles. If this feature is enabled, LMD is reduced by Design Capacity / 1024 every time CYCL
increments by 2 and every time that a cumulative NAC self-discharge estimate reduction of 1.56% has been
made without charging the battery to full. If TAPER[7] is set to 0, there is no LMD reduction with cycle count or
self-discharge.
Pack Configuration (PKCFG) — Address 0x7C
bq27010, bq27210
SLUS707B–APRIL 2006–REVISED JANUARY 2007
BIT 7
GPIEN
BIT 6
QV1
BIT 5
QV0
BIT 4
BOFF(2)
BIT 3
BOFF(1)
BIT 2
BOFF(0)
BIT 1
DCFIX
BIT 0
TCFIX
NAME
GPIEN
Allows the pack manufacturer to set the state of the GPIO pin on initial power up. If the bit is 0, the
GPIEN bit is cleared on reset and the GPIO pin acts as a high-impedance output. If the bit is 1, the
GPIEN bit is set on reset and the GPIO pin acts as an input. The state of the GPIO pin can then be
read through the GPSTAT bit in the MODE register. If PKCFG is updated using the UPCFG host
command (see Device Control section), the updated PKCFG value will not reinitialize GPIEN in the
MODE register.
QV1 & QV0
These bits set the minimum qualification voltage for charge termination. The termination voltage
thresholds are set as listed in
Table 3
.
Table 3. Charge Termination Voltage Settings
QV1
0
0
1
1
QV0
0
1
0
1
Voltage (mV)
3968
4016
4064
4112
BOFF
These bits are used to store a typical board offset value for the gauge. This value is added to the
internal offset measurement and the total applied as an offset correction for the charge and
discharge coulometric measurements made by the DSCC. This is a 2s-complement signed number
with a value of 2.45 μV per bit.
Table 4. Board Offset Voltage Settings
Board Offset
7.35 μV
4.9 μV
2.45 μV
0
-2.45 μV
-4.9 μV
-7.35 μV
-9.8 μV
BOFF(2)
0
0
0
0
1
1
1
1
BOFF(1)
1
1
0
0
1
1
0
0
BOFF(0)
1
0
1
0
1
0
1
0
20
Submit Documentation Feedback
相關PDF資料
PDF描述
27210 Li-Ion AND Li-Pol BATTERY GAS GAUGE IC FOR PORTABLE APPLICATIONS (bqJUNIOR)
270KD05JX 11 to 460 Volts Varistor 0.7 to 29 Joule
271KD05JX 11 to 460 Volts Varistor 0.7 to 29 Joule
270KD05NX 4 to 460 Volts Varistor 0.20 to 22.5 Joule
271KD05NX 4 to 460 Volts Varistor 0.20 to 22.5 Joule
相關代理商/技術參數
參數描述
27-010 制造商:Distributed By MCM 功能描述:3.5mm F to 1/4 in M Stereo Adaptor 制造商:MCM 功能描述:COMPUTERS; Body Style:Straight Adapter; Convert From:3.5mm Female; Convert To:0.25" Male; Pin Size:3.5mm
270-10 功能描述:金屬膜電阻器 - 透孔 10ohms 1% 50PPM RoHS:否 制造商:IRC 電阻:63.4 kOhms 容差:1 % 功率額定值:100 mW 電壓額定值:200 V 溫度系數:100 PPM / C 端接類型:Axial 工作溫度范圍: 尺寸:2.3 mm Dia. x 6.4 mm L 封裝:Bulk
270-10.2 功能描述:金屬膜電阻器 - 透孔 10.2ohms 1% 50PPM RoHS:否 制造商:IRC 電阻:63.4 kOhms 容差:1 % 功率額定值:100 mW 電壓額定值:200 V 溫度系數:100 PPM / C 端接類型:Axial 工作溫度范圍: 尺寸:2.3 mm Dia. x 6.4 mm L 封裝:Bulk
270-10.2/AP 功能描述:金屬膜電阻器 - 透孔 USE 270-10.2/AP-RC 50PPM RoHS:否 制造商:IRC 電阻:63.4 kOhms 容差:1 % 功率額定值:100 mW 電壓額定值:200 V 溫度系數:100 PPM / C 端接類型:Axial 工作溫度范圍: 尺寸:2.3 mm Dia. x 6.4 mm L 封裝:Bulk
270-10.2/AP-RC 功能描述:金屬膜電阻器 - 透孔 10.2ohms 1% 50PPM RoHS:否 制造商:IRC 電阻:63.4 kOhms 容差:1 % 功率額定值:100 mW 電壓額定值:200 V 溫度系數:100 PPM / C 端接類型:Axial 工作溫度范圍: 尺寸:2.3 mm Dia. x 6.4 mm L 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*