參數資料
型號: 27C1610-10
廠商: Macronix International Co., Ltd.
英文描述: 16M-BIT [2M x 8/1M x 16] CMOS OTP ROM
中文描述: 1,600位[2米x 8/1M × 16]的CMOS檢察官辦公室光盤
文件頁數: 3/19頁
文件大?。?/td> 329K
代理商: 27C1610-10
3
P/N:PM0593
REV. 1.4, NOV. 19, 2002
MX27C1610
SYSTEM CONSIDERATIONS
During the switch between active and standby condi-
tions, transient current peaks are produced on the ris-
ing and falling edges of Chip Enable. The magnitude of
these transient current peaks is dependent on the out-
put capacitance loading of the device. At a minimum, a
0.1 uF ceramic capacitor (high frequency, low inherent
inductance) should be used on each device between
Vcc and GND to minimize transient effects. In addition,
to overcome the voltage drop caused by the inductive
effects of the printed circuit board traces on One Time
Programmable Read Only Memory arrays, a 4.7 uF
bulk electrolytic capacitor should be used between VCC
and GND for each eight devices. The location of the
capacitor should be close to where the power supply is
connected to the array.
WRITE OPERATIONS
Commands are written to the COMMAND INTERFACE
REGISTER (CIR) using standard microprocessor write
timings. The CIR serves as the interface between the
microprocessor and the internal chip operation. The
CIR can decipher Read Array, Read Silicon ID and Pro-
gram command. In the event of a read command, the
CIR simply points the read path at either the array or
the silicon ID, depending on the specific read command
given. For a program cycle, the CIR informs the write
state machine, and the write state machine and the write
state machine will control the program sequences and
the CIR will only respond to status reads. After the
write state machine has completed its task, it will allow
the CIR to respond to its full command set. The CIR
stays at read status register mode until the microproc-
essor issues another valid command sequence.
Device operations are selected by writing commands
into the CIR. See command definition table below.
MODE SELECT TABLE
BYTE/
MODE
CE
OE
A9
A0
Q15/A-1
VPP(5)
Q8-14
Q0-7
Read (Word) (2)
VIL
VIL
X
X
Q15 Out
VIH
Q8-14 Out
Q0-7 Out
Read (Upper Byte) (2)
VIL
VIL
X
X
VIH
VIL
High Z
Q8-15 Out
Read (Lower Byte) (2)
VIL
VIL
X
X
VIL
VIL
High Z
Q0-7 Out
Output Disable (2)
VIL
VIH
X
X
High Z
X
High Z
High Z
Standby (2)
VIH
X
X
X
High Z
X
High Z
High Z
Write Operation (2)
VIL
VIH
X
X
Q15 In
VPP
Q8-14 In
Q0-7 In
ManufacturerID(3)(1)
VIL
VIL
VH
VIL
0B
VIH
00H
C2H
Device ID(3)(1)
VIL
VIL
VH
VIH
0B
VIH
00H
6AH
NOTES:
1. VH = 10V ± 0.5V
2. X Either VIL or VIH.
3. A1= VIL, other address lines not specified are at "X" states
4. See DC Programming Characteristics for VPP voltages.
5. BYTE/VPP is intended for operation under DC Voltage conditions only. VPP=10V±
0.5V for write operation
相關PDF資料
PDF描述
27C1610-12 16M-BIT [2M x 8/1M x 16] CMOS OTP ROM
27C16AFT-15IVS The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
27C16AFT-15L Circular Connector; No. of Contacts:11; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:21-11 RoHS Compliant: No
27C16AFT-15P Circular Connector; No. of Contacts:11; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:21-11 RoHS Compliant: No
27C16A-20ITS The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each
相關代理商/技術參數
參數描述
27C1610-12 制造商:MCNIX 制造商全稱:Macronix International 功能描述:16M-BIT [2M x 8/1M x 16] CMOS OTP ROM
27C16A-15IL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16K (2K x 8) CMOS EEPROM
27C16A-15IP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16K (2K x 8) CMOS EEPROM
27C16A-15ITS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16K (2K x 8) CMOS EEPROM
27C16A-15IVS 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16K (2K x 8) CMOS EEPROM