- 您現在的位置：買賣IC網 > PDF目錄371429 > 27LV256-30IP (Microchip Technology Inc.) 256K (32K x 8) Low-Voltage CMOS EPROM PDF資料下載
參數資料
| 型號： | 27LV256-30IP |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 中文描述： | 256K（32K的× 8）低電壓的CMOS存儲器 |
| 文件頁數： | 6/12頁 |
| 文件大小： | 64K |
| 代理商： | 27LV256-30IP |
27LV256
DS11020F-page 6
1996 Microchip Technology Inc.
1.3
Standby Mode
The standby mode is defined when the CE pin is high
(V
IH
) and a program mode is not defined. Output Dis-
able
1.4
Output Enable
This feature eliminates bus contention in multiple bus
microprocessor systems and the outputs go to a high
impedance when the following condition is true:
The OE pin is high and program mode is not
defined.
1.5
Programming Mode
The Express algorithm has been developed to improve
on the programming throughput times in a production
environment. Up to 10 100-microsecond pulses are
applied until the byte is verified. No over-programming
is required. A flowchart of the express algorithm is
shown in Figure 1.
Programming takes place when:
a)
V
CC
is brought to the proper voltage
b)
V
PP
is brought to the proper V
H
level
c)
the OE pin is high
d)
the CE pin is low
Since the erased state is “1” in the array, programming
of “0” is required. The address to be programmed is set
via pins A0-A14 and the data to be programmed is pre-
sented to pins O0-O7. When data and address are sta-
ble, a low-going pulse on the CE line programs that
location.
1.6
Verify
After the array has been programmed it must be veri-
fied to ensure that all the bits have been correctly pro-
grammed. This mode is entered when all of the
following conditions are met:
a)
V
CC
is at the proper level
b)
V
PP
is at the proper V
H
level
c)
the CE pin is high
d)
the OE line is low
1.7
Inhibit
When Programming multiple devices in parallel with
different data, only CE needs to be under separate con-
trol to each device. By pulsing the CE line low on a par-
ticular device, that device will be programmed, and all
other devices with CE held high will not be pro-
grammed with the data although address and data are
available on their input pins.
1.8
Identity Mode
In this mode specific data is outputted which identifies
the manufacturer as Microchip Technology Inc. and
device type. This mode is entered when Pin A9 is
taken to V
H
(11.5V to 12.5V). The CE and OE lines
must be at V
IL
. A0 is used to access any of the two
non-erasable bytes whose data appears on O0 through
O7.
Pin
Input
Output
Identity
A0
0
7
O
6
O
5
O
4
O
3
O
2
O
1
O
0
H
e
x
29
8C
Manufacturer
Device Type*
V
IL
V
IH
0
1
0
0
1
0
0
0
1
1
0
1
0
0
1
0
* Code subject to change.
相關PDF資料 |
PDF描述 |
|---|---|
| 27LV256-30ISO | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-30L | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-30P | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-30SO | 256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-30VS | 256K (32K x 8) Low-Voltage CMOS EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 27LV25630ISO | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| 27LV256-30ISO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV256-30IVS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:256K (32K x 8) Low-Voltage CMOS EPROM |
| 27LV25630L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 EPROM |
| 27LV256-30L | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:256K (32K x 8) Low-Voltage CMOS EPROM |
發布緊急采購，3分鐘左右您將得到回復。