- 您現在的位置：買賣IC網 > PDF目錄371431 > 28C64AFT-15L (Microchip Technology Inc.) Circular Connector; No. of Contacts:11; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:21-11 RoHS Compliant: No PDF資料下載
參數資料
| 型號： | 28C64AFT-15L |
| 廠商： | Microchip Technology Inc. |
| 元件分類： | 圓形連接器 |
| 英文描述： | Circular Connector; No. of Contacts:11; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:21-11 RoHS Compliant: No |
| 中文描述： | 64K的（8K的× 8）的CMOS EEPROM的 |
| 文件頁數： | 6/8頁 |
| 文件大小： | 67K |
| 代理商： | 28C64AFT-15L |
28C64A
DS11109H-page 6
1996 Microchip Technology Inc.
2.0
DEVICE OPERATION
The Microchip Technology Inc.
28C64A
has four basic
modes of operation—read, standby, write inhibit, and
byte write—as outlined in the following table.
2.1
Read Mode
The
28C64A
has two control functions, both of which
must be logically satisfied in order to obtain data at the
outputs. Chip enable (CE) is the power control and
should be used for device selection. Output Enable
(OE) is the output control and is used to gate data to
the output pins independent of device selection.
Assuming that addresses are stable, address access
time (tACC) is equal to the delay from CE to output
(tCE). Data is available at the output t
OE
after the fall-
ing edge of OE, assuming that CE has been low and
addresses have been stable for at least t
ACC
-t
OE
.
2.2
Standby Mode
The
28C64A
is placed in the standby mode by applying
a high signal to the CE input. When in the standby
mode, the outputs are in a high impedance state, inde-
pendent of the OE input.
2.3
Data Protection
In order to ensure data integrity, especially during criti-
cal power-up and power-down transitions, the following
enhanced data protection circuits are incorporated:
First, an internal V
CC
detect (3.3 volts typical) will inhibit
the initiation of non-volatile programming operation
when V
CC
is less than the V
CC
detect circuit trip.
Second, there is a WE filtering circuit that prevents WE
pulses of less than 10 ns duration from initiating a write
cycle.
Third, holding WE or CE high or OE low, inhibits a write
cycle during power-on and power-off (V
CC
).
Operation
Mode
CE
OE
WE
I/O
Rdy/Busy
(1)
Read
L
L
H
D
OUT
H
Standby
H
X
X
High Z
H
Write Inhibit
H
X
X
High Z
H
Write Inhibit
X
L
X
High Z
H
Write Inhibit
X
X
H
High Z
H
Byte Write
L
H
L
D
IN
L
Byte Clear
Automatic Before Each “Write”
Note 1: Open drain output.
2: X = Any TTL level.
2.4
Write Mode
The
28C64A
has a write cycle similar to that of a Static
RAM. The write cycle is completely self-timed and ini-
tiated by a low going pulse on the WE pin. On the fall-
ing edge of WE, the address information is latched. On
rising edge, the data and the control pins (CE and OE)
are latched. The Ready/Busy pin goes to a logic low
level indicating that the
28C64A
is in a write cycle which
signals the microprocessor host that the system bus is
free for other activity. When Ready/Busy goes back to
a high, the
28C64A
has completed writing and is ready
to accept another cycle.
2.5
Data Polling
The
28C64A
features Data polling to signal the comple-
tion of a byte write cycle. During a write cycle, an
attempted read of the last byte written results in the
data complement of I/O7
(I/O0 to I/O6 are indetermin-
able). After completion of the write cycle, true data is
available. Data polling allows a simple read/compare
operation to determine the status of the chip eliminat-
ing the need for external hardware.
2.6
Electronic Signature for Device
Identification
An extra row of 32 bytes of EEPROM memory is avail-
able to the user for device identification. By raising A9
to 12V
±
0.5V and using address locations 1FEO to
1FFF, the additional bytes can be written to or read
from in the same manner as the regular memory array.
2.7
Chip Clear
All data may be cleared to 1's in a chip clear cycle by
raising OE to 12 volts and bringing the WE and CE low.
This procedure clears all data, except for the extra row.
相關PDF資料 |
PDF描述 |
|---|---|
| 28C64A-25IVS | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 28C64AF-25IVS | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 28C64AT-25IVS | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 28C64AFT-25IVS | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 28C64A-20ISO | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28C64AFT-15P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K (8K x 8) CMOS EEPROM |
| 28C64AFT-15SO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K (8K x 8) CMOS EEPROM |
| 28C64AFT-15TS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K (8K x 8) CMOS EEPROM |
| 28C64AFT-15VS | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:64K (8K x 8) CMOS EEPROM |
| 28C64AFT-20/L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EEPROM|8KX8|CMOS|LDCC|32PIN|PLASTIC |
發布緊急采購，3分鐘左右您將得到回復。