參數資料
型號: 29C516E
廠商: ATMEL CORP
元件分類: 通用總線功能
英文描述: 97-3106A14S-5S
中文描述: CMOS SERIES, 16-BIT ERROR DETECT AND CORRECT CKT, PQFP100
封裝: MQFL-100
文件頁數: 8/16頁
文件大?。?/td> 94K
代理商: 29C516E
29C516E
8
Rev. D (09 Dec. 97)
Table 6: Single Bit–Error
MD
[
..
]
[
15
]
[
14
]
[
13
]
[
12
]
[
11
]
[
10
]
[
9
]
[
8
]
[
7
]
[
6
]
[
5
]
[
4
]
[
3
]
[
2
]
[
1
]
[
0
]
SY
(hexa)
34
h
2A
h
29
h
25
h
32
h
1A
h
16
h
13
h
31
h
23
h
15
h
0B
h
2C
h
1C
h
0E
h
0D
h
MC
[
..
]
[
]
[
]
[
5
]
[
4
]
[
3
]
[
2
]
[
1
]
[
0
]
SY
(hexa)
––
h
––
h
20
h
10
h
08
h
04
h
02
h
01
h
7.3. Double–Bit Error
If two errors occurs, there will be either 2, 4 or 6 bits set
to one in the syndrome byte. The syndrome value
generated by a double–bit error does not take place of a
syndrome value generated by a single–bit error. Then,
only the non correctable error flag NCERR will be
activated to indicate that errors are present but cannot
7.4. Triple–Bit Error
be corrected.
Example: If MD[4] and MC[2] are incorrect, syndrome
bits [0], [1], [2] and [3] are set to one (SY=0Fh ), NCERR
is set low and CERR remains at high level.
Triple–Bit Error When three errors are detected, an error
flag is set low as warning to the system. But the generated
syndrome can have the listed value of single–bit error.
The device must be in detect mode to prevent false
correction occurring.
Example: If MD[0], MD[14] and MC[1] are corrupted,
7.5. 4–bit Wide Memory Error
the syndrome value is ”25h ”. This is decoded by the
29C516E EDAC as being a correctable error on MD[12].
The CERR flag is set low and correction would take
place if the device is in correct mode. This would cause
more errors.
The 6 check–bit code can be used to provide error
detection for up to 4 errors occurring in the following
groups: MD[15..12], MD[11..8], MD[7..4], MD[3..0],
MC[5..3] and MC[2..0]. The 29C516E EDAC can flag
any number of errors in 4–bit wide memory chip. A
8. The 8–Bit Syndrome Word
special attention must be taken, multi–bit error ( 3)
located into the defined groups can provide the syndrome
byte of a single–bit error.
Example: If MD[3], MD[2], MD[1] and MD[0] are in
error, the syndrome code is ”33 h ”;
This feature is available when the N22 pin is driven at a
low level.
8.1. No Errors
If there are no errors in the read Data or Check–Bit, all the
syndrome byte is ”00”. The EDAC flags are inactive.
No Error : SY=00
8.2. Single Bit–Error
Single Bit–Error A single bit–error in a Memory Data
word read (MD[..]) causes three syndrome bits to be set
to one. The code formed indicates which bit of the
Memory Data word is incorrect.
For example, if MD[10] were incorrect, the syndrome
byte would have bits 1, 3 and 4 set to one. The syndrome
decoder of 29C516E EDAC decodes the information in
the syndrome byte and only sets low the error flag CERR.
In correct mode (CORRECT pin active), it inverts (and
hence corrects) the relevant bit in error of the Memory
Data word and provides the expected Data word for the
EDAC controller.
If there is an error in the Memory Check–bit (MC[..]),
only one bit of the syndrome is set to one.
In this case, the syndrome decoder sets low the
correctable error flag CERR, but NCERR does not
change. It does not correct the Check–bit because these
bits are not used by the system.
相關PDF資料
PDF描述
29C532E 5-Pin, Multiple-Input, Programmable Reset ICs
29C93 ISDN, Other/Special/Miscellaneous
29F001B-12 1M-BIT [128K x 8] CMOS FLASH MEMORY
29F001B-90 1M-BIT [128K x 8] CMOS FLASH MEMORY
29F001T-12 1M-BIT [128K x 8] CMOS FLASH MEMORY
相關代理商/技術參數
參數描述
29C516E_07 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:16-Bit Flow-Through EDAC Error Detection And Correction unit
29C532E 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Error Detection & Correction (EDAC)
29C60AJC 制造商:Rochester Electronics LLC 功能描述:- Bulk
29C60APC 制造商:Rochester Electronics LLC 功能描述:- Bulk
29C818SC 制造商:Advanced Micro Devices 功能描述:PIPELINE REGISTER